Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X5-10S
The AirTAC Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X5-10S is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 0 to 5 mm on the machine — no shims, no part change.
- BoreØ100 mm
- Max stroke5 mm
- Adjustable range0–5 mm
- Adjuster threadM27×2.0
- Port sizePT3/8
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X5-10S
The AirTAC SDAJ100X5-10S is a compact double-acting single-rod cylinder featuring an external adjustable extend stop. By turning the R (M27x2.0) screw, you dial the extend end-position on-site between 0 and 5 mm without changing parts. Because the adjuster sets the mechanical stop rather than the piston area, output force equals a standard SDA of this bore, delivering 3927 N push at 0.5 MPa.
Designed to save axial mounting depth where larger profile cylinders cannot fit, this riveted-body unit operates at 30-500 mm/s. It relies on a fixed NBR bumper to decelerate the stroke end rather than an adjustable air cushion. The built-in magnet (-S) supports AirTAC reed or electronic switches for position sensing.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X5-10S Technical Specifications
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X5-10S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 5 mm |
| Adjustable range | 0 – 5 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. Force is unchanged from a standard SDA of the same bore. Specifications follow the official AirTAC SDAJ datasheet.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Force matches a standard SDA of the same bore; the adjuster only sets the stop position, not the area. Actual usable force is lower than theoretical due to friction.
Model Code: Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X5-10S
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×5 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X5-10S Is Used
Short-Stroke Clamping
Delivers 3927 N of thrust to secure heavy workpieces, while the 0-5 mm extend tuning allows operators to set the exact clamp depth without shims.
Vertical Lift Stops
Raises loads up to 200.2 kg safely; the R (M27x2.0) screw lets you fine-tune the lift endpoint on the machine to prevent over-travel.
Compact Pressing
Fits into tight axial spaces where larger actuators fail, using the fixed NBR bumper to absorb the shock of high-force end-of-stroke contact.
Is the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X5-10S the Right Cylinder?
When sizing this 100 mm bore actuator, evaluate both neighbors: stepping down to an SDAJ80 yields 2513.3 N push at 0.5 MPa, whereas this 100 mm bore provides 3927 N. This makes the SDAJ100X5-10S the correct choice when the smaller variant lacks thrust. With a safe working load of roughly 2356 N (about 60% of the 0.5 MPa figure), it can vertically lift approximately 200.2 kg with a 2:1 margin.
This model suits setups needing exact on-site stroke tuning over a 0-5 mm window. Confirm the PT3/8 port, 32 mm rod, female M18x1.5 rod-end thread, and the -S magnet. Remember that a plain cylinder drifts on air loss or valve centering; the fixed bumper only decelerates near the end and is not a lock. For load holding without live pressure, install an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Need on-machine stroke fine-tuning?
- ✓ Target position within 0–5 mm
- ✓ Force at your working pressure
- ✓ Access to reach the R adjuster
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Lock the M27×2.0 adjuster after setting the stroke.
- check Avoid side load on the piston rod.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X5-10S FAQ
This 100 mm bore double-acting cylinder provides 3927 N push and 3524.9 N pull at 0.5 MPa, 5497.8 N push and 4934.8 N pull at 0.7 MPa, with a theoretical maximum of 801 kgf at 1.0 MPa.
The M27x2.0 adjuster screw shortens the extend stop by up to 10 mm, yielding a usable 0-5 mm extend range while retract remains full. The included -S magnet works with AirTAC reed or electronic switches for position detection.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAJ Cylinders
Request a Quote for Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X5-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.