
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X55-30 is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 25 to 55 mm on the machine — no shims, no part change.
The AirTAC SDAJ100X55-30 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M27x2.0) screw, you can dial the outward stroke down from the 55mm maximum to as low as 25mm directly on the machine, avoiding part swaps during setup changes.
This riveted-body design saves substantial axial mounting depth compared to conventional round-body or profile alternatives, fitting high-force actuation into tight machinery envelopes. The end-of-stroke deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches without switching to the -S variant.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X55-30 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 55 mm |
| Adjustable range | 25 – 55 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | — |
| Max (@1.0 MPa) | 719 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×55 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Adjust the mechanical stop on the fly to accommodate varying cast iron part heights, ensuring rigid 801 kgf maximum clamping pressure in a compact footprint.
When sizing this model, evaluate your force requirements both ways. Stepping up is not an option as this is the largest bore in the series, making this the maximum force choice within the compact family. This cylinder is ideal for heavy pressing or clamping tasks that require frequent on-machine stroke tuning between 25 and 55mm.
Confirm the bore (100mm), full stroke (55mm), adjustment window (30mm), and PT3/8 port before ordering. The rod end thread is female M18x1.5 (or male M26x1.5 if option B is specified). Remember that a plain SDAJ does not hold a load if air pressure drops or the valve is centered; the fixed NBR bumper only decelerates the stroke end. For suspended or vertical loads, you must integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ100 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj100-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 5497.8 N and pull to 4934.8 N. The theoretical maximum push force is 801 kgf at 1.0 MPa.
The external R (M27x2.0) screw mechanically limits the extend stroke, allowing you to set the outward travel anywhere between 25mm and 55mm. This screw only acts as a stop and does not alter the output force or lock the piston mid-stroke.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.