
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X55-75S is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 0 to 55 mm on the machine — no shims, no part change.
The AirTAC SDAJ100X55-75S is a double-acting compact cylinder featuring an external adjustable extend stop. An M27x2.0 adjuster screw lets you dial the rod extension from 0 to 55 mm directly on the machine, eliminating the need for shims or part swaps during setup.
The short riveted body saves valuable axial mounting depth where a larger profile cylinder will not fit. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. This unit includes a built-in piston magnet for compatibility with AirTAC reed or electronic switches, operating at speeds between 30 and 500 mm/s.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X55-75S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 55 mm |
| Adjustable range | 0 – 55 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 75 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | — |
| Max (@1.0 MPa) | 719 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×55 | Maximum stroke length in mm. |
| -75 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Adjust the extend position on-site to accommodate varying pallet widths on a packaging line, using the fixed NBR bumper to absorb the stop impact.
Safely test vertical lift points up to 200.2 kg by tuning the stroke down from the maximum 55 mm to find the exact engagement height before locking the routine.
Stepping up to this 100 mm bore is necessary when the smaller variant cannot overcome your process drag, while maintaining a compact footprint.
This model suits operators who require frequent on-machine stroke tuning during product changeovers. Remember that a plain cylinder does not hold its load on air loss or when the valve is centered; the fixed bumper only decelerates near the end of travel. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve. Configuration: 100 mm bore, 55 mm max stroke, 75 mm window, PT3/8 port, female M18x1.5 rod thread, and an -S magnet for sensing.
AirtacDistr lists every SDAJ100 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj100-adjustable-cylinder
Quick checklist
The theoretical maximum push force is 801 kgf at 1.0 MPa.
The M27x2.0 screw shortens the extend stop by up to 75 mm, allowing usable extensions from 0 to 55 mm; retract remains full stroke. The included -S magnet works with AirTAC reed or electronic switches for position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.