
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50 is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 10 to 60 mm on the machine — no shims, no part change.
The AirTAC SDAJ100X60-50 is a compact double-acting double-rod cylinder built for heavy-duty positioning where the extend endpoint requires on-site dialling. An external R (M27x2.0) adjuster screw lets you shorten the forward stroke by up to 50 mm, yielding a usable extend range of 10 to 60 mm without changing parts.
The short riveted body significantly reduces axial mounting depth compared to conventional round-body or profile cylinders, fitting large-bore power into tight machine footprints. End-of-travel deceleration is handled by a fixed NBR bumper at each end, which absorbs shock but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic sensing without upgrading to the -S variant.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 60 mm |
| Adjustable range | 10 – 60 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | — |
| Max (@1.0 MPa) | 719 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×60 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Quickly readjust the extend stop via the M27x2.0 screw when swapping large production fixtures, saving axial space in the cell with the compact riveted body.
Choose this model if your fixture or press requires frequent changeovers and precise endpoint tuning directly on the machine floor. Confirm your parameters match the 100 mm bore, 60 mm maximum stroke, 50 mm adjust window, and PT3/8 port. Keep in mind that a plain SDAJ does not hold position or load when air is lost or the valve is centred; the fixed bumper only decelerates near the end of travel. For load holding without live pressure, install an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ100 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj100-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 5497.8 N and pull to 4934.8 N. The theoretical maximum push is 801 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa, with a proof pressure of 1.5 MPa and an operating speed of 30-500 mm/s.
Turning the external R (M27x2.0) screw mechanically shortens the extend stop, allowing you to set the forward stroke anywhere between 10 and 60 mm. The screw acts only as a mechanical end stop and does not alter the cylinder's force or lock the piston mid-stroke. For load holding on air loss, you must use an external rod lock or pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.