Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X65-40S
The AirTAC Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X65-40S is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 25 to 65 mm on the machine — no shims, no part change.
- BoreØ100 mm
- Max stroke65 mm
- Adjustable range25–65 mm
- Adjuster threadM27×2.0
- Port sizePT3/8
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X65-40S
The SDAJ100X65-40S is a 100 mm bore double-acting compact cylinder with an external adjustable extend stop. Turning the R (M27x2.0) screw lets you dial the outward stroke anywhere between 25 and 65 mm directly on your machine, eliminating the need for shims or part swaps. Because the adjuster only sets the mechanical stop position, output force remains identical to a standard SDA of this bore, delivering 3927 N of push at 0.5 MPa.
This riveted-body design saves valuable axial mounting depth where larger profile cylinders cannot fit. The unit includes a built-in piston magnet for AirTAC reed or electronic switches and relies on a fixed NBR bumper at each end to decelerate the stroke. It is not a mid-stroke lock, so maintaining vertical loads requires an external rod lock or pilot-operated check valve.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X65-40S Technical Specifications
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X65-40S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 65 mm |
| Adjustable range | 25 – 65 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. Force is unchanged from a standard SDA of the same bore. Specifications follow the official AirTAC SDAJ datasheet.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Force matches a standard SDA of the same bore; the adjuster only sets the stop position, not the area. Actual usable force is lower than theoretical due to friction.
Model Code: Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X65-40S
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×65 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X65-40S Is Used
Press Fit Tuning
Dial the 25-65 mm extend stop to set precise contact depth for inserting heavy bearings without over-stressing the 3927 N force output.
Heavy Assembly Changeover
Quickly adjust the outward stroke on the production floor when switching between thick and thin product variants, avoiding teardown time.
Vertical Lift Positioning
Set exact lifting heights for 200.2 kg loads, relying on an external check valve to hold the payload safely when air pressure drops.
Is the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X65-40S the Right Cylinder?
When sizing this actuator, evaluate your force requirements both ways. Stepping down to an SDAJ80 yields 2513.3 N of push at 0.5 MPa, which may be insufficient for heavy pressing tasks, whereas this 100 mm bore provides a safe working load of roughly 2356 N (about 60% of its 3927 N capacity) and a vertical lift capacity of approximately 200.2 kg with a 2:1 safety margin. Choose this specific model if your fixture requires on-site stroke tuning during frequent changeovers.
Confirm your parameters before ordering: 100 mm bore, 65 mm maximum stroke with a 40 mm adjust window, PT3/8 air port, and a female M18x1.5 rod-end thread. The -S suffix indicates the magnet is present for position sensing. Remember that the fixed NBR bumper absorbs end-shock but does not hold position upon air loss.
Quick checklist
- ✓ Need on-machine stroke fine-tuning?
- ✓ Target position within 25–65 mm
- ✓ Force at your working pressure
- ✓ Access to reach the R adjuster
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Lock the M27×2.0 adjuster after setting the stroke.
- check Avoid side load on the piston rod.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X65-40S FAQ
This 100 mm bore double-acting cylinder provides 3927 N push and 3524.9 N pull at 0.5 MPa, 5497.8 N push and 4934.8 N pull at 0.7 MPa, with a theoretical maximum push of 801 kgf at 1.0 MPa.
The M27x2.0 adjuster screw mechanically shortens the extend stroke from the 65 mm maximum down to 25 mm without altering force. The built-in -S magnet allows tracking of the piston position using AirTAC reed or electronic solid-state switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAJ Cylinders
Request a Quote for Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X65-40S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.