
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X80-40B is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 40 to 80 mm on the machine — no shims, no part change.
The AirTAC SDAJ100X80-40B is a double-acting compact cylinder featuring an external adjustable extend stop. A M27x2.0 adjuster screw lets you dial the outward stroke anywhere between 40 and 80 mm directly on the machine.
This variant uses a male M26x1.5 piston rod thread and a PT3/8 air port. The short riveted body significantly reduces axial mounting depth compared to conventional round-body units. End-of-travel deceleration is handled by a fixed NBR bumper, which is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic switches.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X80-40B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 80 mm |
| Adjustable range | 40 – 80 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | — |
| Max (@1.0 MPa) | 719 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×80 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Secure oversized workholding fixtures where axial space is restricted, benefiting from the compact riveted body and the robust 32 mm male rod end.
Stepping down, the SDAJ80 provides 2513.3 N, which may be insufficient for heavy loads, whereas stepping up is impossible as 100 mm is the largest available bore in this series. This model is ideal for setups requiring on-site stroke tuning to perfect end positions without machining new parts. Keep in mind the male M26x1.5 rod thread and 40 mm adjustment window for your mounting interfaces.
Regarding load management, the fixed NBR bumper only decelerates the piston near the end of travel and the R screw acts solely as a mechanical stop. A plain cylinder does not hold position if air pressure drops or the valve is centered. To safely suspend loads, you must integrate an external rod lock or a pilot-operated check valve into your pneumatic circuit.
AirtacDistr lists every SDAJ100 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj100-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 5497.8 N and pull to 4934.8 N. The theoretical maximum push force is 801 kgf at 1.0 MPa.
The M27x2.0 adjuster screw mechanically shortens the extend stop from the 80 mm maximum down to 40 mm without altering the output force. This specific SKU lacks the -S magnet option, so it cannot accept AirTAC reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.