
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X80-75S is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 5 to 80 mm on the machine — no shims, no part change.
The AirTAC SDAJ100X80-75S is a double-acting, double-rod compact cylinder featuring an external adjustable extend stop. By turning the R (M27x2.0) screw, you can dial the extend position anywhere between 5 and 80 mm directly on the machine, avoiding part changes.
This 100 mm bore unit utilizes a short riveted body to minimize axial mounting depth where larger profile cylinders cannot fit. It includes a fixed NBR bumper at each end to decelerate the stroke end, though this acts as a mechanical stop rather than an adjustable air cushion. Equipped with a built-in piston magnet (-S), the body grooves readily accept AirTAC reed or electronic solid-state switches for position sensing.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X80-75S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 80 mm |
| Adjustable range | 5 – 80 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 75 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | — |
| Max (@1.0 MPa) | 719 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×80 | Maximum stroke length in mm. |
| -75 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Quickly reposition the extend stop for varying product heights on a single line, using the external R screw to adapt the motion profile on the fly.
When sizing this model, compare the output against adjacent bores. Choose this specific unit if your assembly process requires frequent on-machine stroke tuning between 5 and 80 mm.
Remember that a plain compact cylinder cannot hold a load if air pressure drops or the valve is centered; the piston will drift, and the fixed bumper only decelerates near the end of travel. For load holding without live pressure, you must integrate an external rod lock or a pilot-operated check valve. Confirm your requirements for the PT3/8 port, the 80 mm maximum stroke with a 75 mm window, the built-in magnet, and the female M18x1.5 rod-end thread before ordering.
AirtacDistr lists every SDAJ100 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj100-adjustable-cylinder
Quick checklist
At 0.7 MPa, the push increases to 5497.8 N. The theoretical maximum push force is 801 kgf at 1.0 MPa.
The M27x2.0 adjuster screw shortens the extend stroke by up to 75 mm, allowing a usable range of 5 to 80 mm without changing parts. The built-in magnet (-S) allows you to mount AirTAC reed or electronic solid-state switches directly into the body grooves for precise end-position detection.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.