
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X85-20 is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 65 to 85 mm on the machine — no shims, no part change.
The AirTAC SDAJ100X85-20 is a compact double-acting double-rod cylinder engineered with an external adjustable extend stop. By turning the R (M27x2.0) screw, you can dial the forward end-position anywhere between 65 and 85 mm directly on the machine, avoiding part swaps during changeovers.
This 100 mm bore actuator features a short riveted body that drastically reduces axial mounting depth compared to conventional round-body or profile cylinders, fitting into tight machinery footprints. End-of-travel deceleration is handled by a fixed NBR bumper at each end, which absorbs shock but is not an adjustable air cushion. Operating speed spans 30-500 mm/s, and the PT3/8 air port is paired with a robust 32 mm piston rod to handle high thrust loads.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X85-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 85 mm |
| Adjustable range | 65 – 85 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | — |
| Max (@1.0 MPa) | 719 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×85 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop between 65 and 85 mm to set precise contact depth for pressing bearings without swapping physical shims.
When sizing this actuator, evaluate your thrust requirements bidirectionally. If you require maximum thrust, this 100 mm bore yields a theoretical 801 kgf at 1.0 MPa.
This model is ideal for operators needing on-site stroke tuning to perfect a pressing or lifting motion. Note that a plain cylinder does not hold its load upon air loss or valve centering; the piston drifts and the fixed bumper only decelerates near the end of the stroke, so integrate an external rod lock or pilot-operated check valve for suspended loads. This configuration includes a 100 mm bore, 85 mm stroke, 20 mm adjust window, PT3/8 port, female M18x1.5 rod-end thread, and no piston magnet.
AirtacDistr lists every SDAJ100 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj100-adjustable-cylinder
Quick checklist
At 0.7 MPa, push is 5497.8 N and pull is 4934.8 N. The theoretical maximum push is 801 kgf at 1.0 MPa.
The external M27x2.0 adjuster screw mechanically shortens the extend stroke by up to 20 mm, allowing you to set the forward stop anywhere from 65 to 85 mm. It does not alter the thrust force, and retract remains full stroke.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.