
Genuine AirTAC fixed mounting height stopper cylinder, order code TTQ32X15SR from the TTQ32 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.
The TTQ32X15SR pairs the Dia 32 mm TTQ32 stopper cylinder with the R roller head and a 15 mm stroke. As a pull-in single acting cylinder, air at the PT1/8 port retracts the rod and the spring extends it again when the supply is cut, so on a 0.2-1.0 MPa line the stopper rises whenever air fails. The roller head lets a moving workpiece ride up against the stopper with rolling contact instead of a sliding strike.
The S magnet is built into the piston for use with the sensor grooves machined on two sides of the body, giving switch feedback on stopper position. The unit mounts through holes or the tapped holes at both ends, runs on air filtered by a 40 um element, needs no lubrication, and operates from -20 to +70 C with a bumper cushion.
| Order code | TTQ32X15SR |
|---|---|
| Product | Fixed mounting height Stopper Cylinder |
| Stroke | 15 mm |
| Stopper | Roller |
| Magnet | Magnet |
| Action | Single acting, spring extend |
|---|---|
| Mounting | Through holes, tapped both ends |
| Bore | Ø32 mm |
| Strokes | 10, 15, 20 mm (+1.0/0) |
| Port | PT1/8 |
| Stopper types | Round rod, Flat rod, Roller, Lever roller, adjustable oil cushion |
| Fluid | Air (filtered by 40 µm element) |
| Operating pressure | 0.25-1.0 MPa on Ø20, 0.2-1.0 MPa on other bores |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to +70 °C |
| Cushion | Bumper |
| Lubrication | Not required |
Source: AirTAC Products Catalog 2026A (PDF01-P0760..P0761), TTQ series specifications and ordering code.
Choose TTQ32X15SR over TTQ32X15SC or TTQ32X15SB when loads should roll onto the stopper rather than hit a fixed rod face. If the impact is hard or the line runs fast, the K lever roller head with adjustable oil cushion in TTQ32X15SK, or TTQ32X15SKF with self-lock, stops more gently. Stroke can be shortened to 10 mm or lengthened to 20 mm by ordering X10 or X20, and dropping the S gives a version without magnet.
AirtacDistr lists every TTQ32 order code with its price on one page at https://airtacdistr.com/products/airtac-ttq32-stopper-cylinder
On powered or gravity roller conveyors, cartons roll onto the R roller head and are caught without the sharp sliding impact a round or flat rod face would deliver.
The S magnet together with the sensor grooves on both sides of the body lets a magnetic switch verify whether the stopper is retracted or extended before the next cycle starts.
In pick-and-pass areas, cutting the air lets the spring raise the 15 mm roller stopper so the next carton passes on cue, and reapplying air drops it back into the flow.
Dia 32 mm bore, 15 mm stroke with +1.0/0 tolerance, R roller head, magnet fitted, PT1/8 port, 0.2-1.0 MPa operating pressure, 1.5 MPa proof pressure, -20 to +70 C, bumper cushion, through-hole or both-ends tapped mounting.
The roller presents a rolling surface, so the workpiece rolls against it instead of striking a fixed rod face as on the C round rod or B flat rod versions. For heavy, fast impacts the K lever roller with adjustable oil cushion stops more softly; the catalog impact load and speed charts help size the bore for the job.