
Genuine AirTAC fixed mounting height stopper cylinder, order code TWQ32X10SR from the TWQ32 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.
The TWQ32X10SR is an AirTAC TWQ32 stopper cylinder with the R option: a roller stopper head that lets incoming loads ride or slide over the rising stopper instead of grinding against a fixed rod. It is double acting on a 32 mm bore with a 10 mm stroke (tolerance +1.0/0 mm), fed through a PT1/8 port, and the S code position confirms a magnet is installed for position sensing along the two sensor grooves of the body.
There is no oil shock absorber in this head, so the roller meets the load directly - which keeps the mechanism simple and is the right choice when loads arrive at moderate speed or enter sideways across the roller. Operating range is 0.15-1.0 MPa with 1.5 MPa (215 psi) proof pressure and -20 to +70 C temperature, on filtered air with no lubrication needed. Mounting uses the through holes or the tapped holes at both ends; check exact roller dimensions in the datasheet.
| Order code | TWQ32X10SR |
|---|---|
| Product | Fixed mounting height Stopper Cylinder |
| Stroke | 10 mm |
| Stopper | Roller |
| Magnet | Magnet |
| Action | Double acting |
|---|---|
| Mounting | Through holes, tapped both ends |
| Bore | Ø32 mm |
| Strokes | 10, 15, 20 mm (+1.0/0) |
| Port | PT1/8 |
| Stopper types | Round rod, Flat rod, Roller, Lever roller, adjustable oil cushion |
| Fluid | Air (filtered by 40 µm element) |
| Operating pressure | 0.15-1.0 MPa |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to +70 °C |
| Cushion | Bumper |
| Lubrication | Not required |
Source: AirTAC Products Catalog 2026A (PDF01-P0760..P0761), TWQ series specifications and ordering code.
TWQ32X10SR is the middle option of the TWQ32 head family: a free-rolling roller rather than the fixed round rod of TWQ32X10SC or flat rod of TWQ32X10SB, but without the lever and adjustable oil cushion of TWQ32X10SK. Choose it when loads roll or slide in sideways and you want minimal scrubbing, but the impact speed is low enough that an oil damper is unnecessary. If loads hit the stopper head-on at speed or can lever it upward, move to TWQ32X10SK, or TWQ32X10SKF if the stopped load must also be held against rollback. Keep the 10 mm stroke for shallow gates; the same bore is offered with 15 mm and 20 mm strokes.
AirtacDistr lists every TWQ32 order code with its price on one page at https://airtacdistr.com/products/airtac-twq32-stopper-cylinder
Stopping boxes that slide in across the roller on a transfer conveyor, where the rolling head avoids the scrub and wear a fixed rod would suffer.
Lifting and lowering the roller as a release stop on a slow-moving line, with the magnet and body sensor grooves confirming gate position each cycle.
Holding totes or pallets at a manual pick position, where operators need a rolling contact surface rather than a sharp stopper rod.
Double acting, 32 mm bore, 10 mm stroke (tolerance +1.0/0 mm), PT1/8 port, roller stopper head, magnet fitted. Operating pressure 0.15-1.0 MPa, proof pressure 1.5 MPa (215 psi), temperature -20 to +70 C, bumper cushion, no lubrication required.
The R head is a plain free roller that suits loads entering sideways at moderate speed; the K head adds a lever with an adjustable oil shock absorber for softer, tunable stops on faster or head-on impacts. Both share the same TWQ32 body: 32 mm bore, sensor grooves on two sides, and the same pressure and temperature limits.