
The AirTAC 4V100 Solenoid Valve 4V130PM5-X0 is a genuine 5/3-way 5/3 double solenoid — pressure center solenoid valve with M5 ports and an effective area of 8.6 mm² (Cv 0.51). It is an internally piloted spool valve that directs compressed air to double-acting cylinders and actuators.
The 4V130PM5-X0 pairs the 4V100 aluminum body with an M5 port size and the 5/3 pressure-center function. Double solenoids pulse the spool; at rest, both working ports remain connected to supply pressure, so the double-acting cylinder equalizes and yields to light external force instead of sitting rigid. That suits fixtures where an operator must slide the actuator aside, and it is explicitly not a stand-alone safety brake for suspended loads.
Flow capacity is Cv 0.51 (catalog figure for the 4V130C-06) (8.6 mm2) with a maximum cycling rate of 3 cycles per second - enough for ~O16-32 mm double-acting cylinders, where an O25 bore gives about 25 kgf push at 0.5 MPa. This listing carries no coil voltage, so confirm AC220V, DC24V or another option at order time. Operating pressure spans 0.15-0.8 MPa, proof pressure 1.2 MPa, protection is IP65 and insulation class B.
| Model | Airtac 4V100 Solenoid Valve 4V130PM5-X0 |
|---|---|
| Series | 4V100 solenoid valve (spool type) |
| Valve type | 5/3-way |
| Function | 5/3 double solenoid — Pressure center |
| Port size | M5 |
| Exhaust port | M5 |
| Effective area (Cv) | 8.6 mm² (Cv 0.51) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Pilot type | Internal / external pilot |
| Operating pressure | 0.15 – 0.8 MPa |
| Proof pressure | 1.2 MPa |
| Max frequency | 3 cycle/sec |
| Response time | ≤ 0.05 s (activating) |
| Temperature | -20 to +70 °C |
| Body material | Aluminum alloy |
| Weight | 200 g |
Specifications follow the official AirTAC 4V series datasheet. Lubrication not required. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
| Effective area | 8.6 mm² |
|---|---|
| Flow coefficient | Cv 0.51 |
| Response time | ≤ 0.05 s |
| Coil power | AC 3.5 VA · DC24V 2.8 W · DC12V 2.5 W |
| Protection / insulation | IP65 (DIN40050), B-class |
| Voltage options | DC24V, DC12V, AC110V, AC220V |
| Manual override | Yes (locking / non-locking) |
Size the valve so effective area / Cv is not the bottleneck for your cylinder bore and speed. Undersized valves slow the actuator. Note 5/3 (center) versions have a smaller effective area than the 5/2 of the same body size.
| 4V | Solenoid valve, spool type, 4-series. |
|---|---|
| 1 | Body size (4V100) — sets port & flow. |
| 3 | Function: 1 = single 5/2, 2 = double 5/2, 3 = 5/3. |
| -M5 | Port thread: M5 / 06=1/8" / 08=1/4" / 10=3/8" / 15=1/2". |
Related: 4V110 (single), 4V120 (double), 4V130C/E/P (5/3 center). Add the voltage suffix when ordering.
A compact pusher diverting small PCBs on a conveyor lane; M5 ports keep the valve footprint tight, and Cv 0.51 (catalog figure for the 4V130C-06) covers an O16-20 mm cylinder's push of roughly 10-16 kgf at 0.5 MPa.
Several 4V130P bodies on one integrated manifold base run the small clamps and ejector pins of an electronics assembly jig from a single filtered supply.
Fine index-and-adjust slides on a packaging machine turret use the pressure center so operators can hand-trim position during changeover instead of deadheading the valve.
Size by bore and speed: at Cv 0.51 (catalog figure for the 4V130C-06) this valve pairs with ~O16-32 mm double-acting cylinders - an O16 gives about 10 kgf push at 0.5 MPa, an O32 about 41 kgf. Below O16 there is no smaller 4V100 valve; above O32, or past 3 cycles per second, step up to the 4V200 series at Cv 1.0. The 1/8"-ported 4V130C-06 shares the same 5/3 flow if you prefer standard push-in fittings over M5. If the actuator must hold rigidly at center, choose the closed-center 4V130C instead; the exhaust-center 4V130E lets it float freely. Match any replacement on five points: 4V100 body, 30P function, M5 port, coil voltage, and entry style (terminal box or grommet lead).
AirtacDistr lists every 4V130P-M5 order code with its price on one page at https://airtacdistr.com/products/airtac-4v130p-m5-solenoid-valve
Quick checklist
It is a 5/3-way double-solenoid valve for double-acting cylinders and actuators in the ~O16-32 mm range. Flow is Cv 0.51 (catalog figure for the 4V130C-06) (8.6 mm2 effective area), cycling reaches 3 per second, response is under 0.05 s, and the supply must be 0.15-0.8 MPa, filtered through a 40 um element with no lubrication added.
Match five things on the old label: the 4V100 body size, the 30P function, the M5 port, the coil voltage (this listing leaves it unspecified, so confirm AC220V, AC110V, AC24V, DC24V or DC12V) and the entry style. G-thread and NPT variants exist only on the 1/8" 06 models, never on M5.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.