
The AirTAC 4V230E-08 Solenoid Valve, 4V200 Series (4V230E08B-W) is a genuine 5/3-way 5/3 double solenoid — exhaust center solenoid valve with PT1/4 ports and an effective area of 13.6 mm² (Cv 0.8). It is an internally piloted spool valve that directs compressed air to double-acting cylinders and actuators.
The 4V230E08B-W is an AirTAC 4V200-series 5/3-way double-solenoid valve in the exhaust-center configuration, built for directional control of double-acting cylinders and actuators. Its two solenoids pulse the spool left or right, and at center both cylinder ports A and B vent to exhaust, so the actuator floats free and can be moved by hand or by an external force. The -W suffix adds a factory external-pilot supply: pilot air arrives through a dedicated port rather than being tapped from the main line, keeping switching dependable in vacuum lines, low-pressure circuits or anywhere main-line pressure dips below the internal-pilot threshold. Fitted with the B coil option (DC24V, 3.0 W) and a hard-wired terminal box entry on PT 1/4 ports.
With an effective area of 13.6 mm2 (Cv 0.8, catalog figure for the 4V230C-08) and a maximum cycling rate of 3 cycles per second, this mid-body valve suits roughly O32-50 mm bores. Actuating response is 0.05 s or better, the body is aluminium alloy rated IP65, and the 360 g valve mounts singly or on an integrated manifold base. Keep in mind that an exhaust center unloads the cylinder at rest - it is a float function, not load holding; where a suspended load must stay put, add a pilot-operated check valve or mechanical brake at the cylinder.
| Model | AirTAC 4V230E-08 Solenoid Valve, 4V200 Series (4V230E08B-W) |
|---|---|
| Series | 4V200 solenoid valve (spool type) |
| Valve type | 5/3-way |
| Function | 5/3 double solenoid — Exhaust center |
| Port size | PT1/4 |
| Exhaust port | PT1/8 |
| Effective area (Cv) | 13.6 mm² (Cv 0.8) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Pilot type | Internal / external pilot |
| Operating pressure | 0.15 – 0.8 MPa |
| Proof pressure | 1.2 MPa |
| Max frequency | 3 cycle/sec |
| Response time | ≤ 0.05 s (activating) |
| Temperature | -20 to +70 °C |
| Body material | Aluminum alloy |
| Weight | 360 g |
Specifications follow the official AirTAC 4V series datasheet. Lubrication not required. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
| Effective area | 13.6 mm² |
|---|---|
| Flow coefficient | Cv 0.8 |
| Response time | ≤ 0.05 s |
| Coil power | AC 4.5 VA · DC24V 3.0 W · DC12V 2.5 W |
| Protection / insulation | IP65 (DIN40050), B-class |
| Voltage options | DC24V, DC12V, AC110V, AC220V |
| Manual override | Yes (locking / non-locking) |
Size the valve so effective area / Cv is not the bottleneck for your cylinder bore and speed. Undersized valves slow the actuator. Note 5/3 (center) versions have a smaller effective area than the 5/2 of the same body size.
| 4V | Solenoid valve, spool type, 4-series. |
|---|---|
| 2 | Body size (4V200) — sets port & flow. |
| 3 | Function: 1 = single 5/2, 2 = double 5/2, 3 = 5/3. |
| -08 | Port thread: M5 / 06=1/8" / 08=1/4" / 10=3/8" / 15=1/2". |
Related: 4V210 (single), 4V220 (double), 4V230C/E/P (5/3 center). Add the voltage suffix when ordering.
Exhaust center lets operators nudge a double-acting clamp or positioner by hand while the valve rests neutral, then re-energise a solenoid to resume the automatic stroke.
The external-pilot -W supply keeps the spool switching even when conveyor-line pressure sags, venting the pusher cylinder freely between pushes instead of locking it mid-track.
Where the main line runs under vacuum or very low pressure, piloting the 4V230E08B-W externally gives a DC24V control system dependable 5/3 float-center switching without inventing supply from the process line.
Choose this exhaust-center model when your double-acting cylinder should drift freely and be repositioned while the valve sits in its neutral state - ideal for parts that need manual adjustment mid-cycle. If the cylinder must instead freeze in position, the 30C closed-center variant blocks all ports; if both chambers should stay pressurized, the 30P pressure center is the match. Step down to the 4V100 (Cv 0.6) for small bores or up to the 4V300 (Cv 1.65) when a larger cylinder or faster stroke demands it.
Specifying the -W external-pilot version matters when supply pressure runs low or under vacuum: feed the pilot port from an independent air source and the spool switches cleanly regardless of main-line conditions. For an exact replacement, match all five points: 4V200 body, 5/3 exhaust-center double-solenoid function, 1/4in PT port with the -W pilot option, DC24V coil, and terminal-box electrical entry.
Quick checklist
A standard 4V230E taps its pilot air internally from the incoming supply. The -W version closes that path off and provides a separate external pilot port you feed from an independent source. That is why it stays reliable on vacuum lines and low-pressure mains where an internal-pilot spool might not receive enough pilot force. The flow data is unchanged: 13.6 mm2 effective area, Cv 0.8 (catalog figure for the 4V230C-08), up to 3 cycles per second.
With both solenoids off, the exhaust-center spool vents cylinder ports A and B to exhaust, so a double-acting cylinder floats free rather than locking. That is a designed float, not a brake: if the actuator carries a suspended load, fit a pilot-operated check valve or a mechanical brake, because this valve alone will not hold it. The DC24V coil draws 3.0 W and wires through the terminal box.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.