
The AirTAC 4V230P-08 Solenoid Valve, 4V200 Series (4V230P08B-AM) is a genuine 5/3-way 5/3 double solenoid — pressure center solenoid valve with PT1/4 ports and an effective area of 13.6 mm² (Cv 0.8). It is an internally piloted spool valve that directs compressed air to double-acting cylinders and actuators.
The 4V230P-08B-AM is a 5/3-way double solenoid valve in the 4V200 body class, built with a pressure center: when both solenoids are off, the supply keeps feeding both cylinder ports while the exhaust stays blocked, so each side of a double-acting actuator remains pressurised. Either coil, pulsed on its own, shifts the spool and holds that new position with no holding current. Its flow class is 13.6 mm2 effective area (Cv 0.8, catalog figure for the 4V230C-08) with a maximum cycling rate of 3 cycles per second, a good match for double-acting cylinders in roughly the 32-50 mm bore range.
This variant carries the -AM factory option: an AMISCO (Italian) solenoid coil is fitted in place of the standard coil, ordered here at DC24V with a terminal-box electrical entry and PT (Rc tapered) 1/4 ports. The valve otherwise matches the standard 4V230P-08B exactly, weighing 360 g, responding in 0.05 s or less, and rated IP65 for dusty or wash-down-adjacent industrial panels. The exact electrical rating of the AMISCO coil is not published in our datasheet, so confirm it with us when ordering.
| Model | AirTAC 4V230P-08 Solenoid Valve, 4V200 Series (4V230P08B-AM) |
|---|---|
| Series | 4V200 solenoid valve (spool type) |
| Valve type | 5/3-way |
| Function | 5/3 double solenoid — Pressure center |
| Port size | PT1/4 |
| Exhaust port | PT1/8 |
| Effective area (Cv) | 13.6 mm² (Cv 0.8) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Pilot type | Internal / external pilot |
| Operating pressure | 0.15 – 0.8 MPa |
| Proof pressure | 1.2 MPa |
| Max frequency | 3 cycle/sec |
| Response time | ≤ 0.05 s (activating) |
| Temperature | -20 to +70 °C |
| Body material | Aluminum alloy |
| Weight | 360 g |
Specifications follow the official AirTAC 4V series datasheet. Lubrication not required. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
| Effective area | 13.6 mm² |
|---|---|
| Flow coefficient | Cv 0.8 |
| Response time | ≤ 0.05 s |
| Coil power | AC 4.5 VA · DC24V 3.0 W · DC12V 2.5 W |
| Protection / insulation | IP65 (DIN40050), B-class |
| Voltage options | DC24V, DC12V, AC110V, AC220V |
| Manual override | Yes (locking / non-locking) |
Size the valve so effective area / Cv is not the bottleneck for your cylinder bore and speed. Undersized valves slow the actuator. Note 5/3 (center) versions have a smaller effective area than the 5/2 of the same body size.
| 4V | Solenoid valve, spool type, 4-series. |
|---|---|
| 2 | Body size (4V200) — sets port & flow. |
| 3 | Function: 1 = single 5/2, 2 = double 5/2, 3 = 5/3. |
| -08 | Port thread: M5 / 06=1/8" / 08=1/4" / 10=3/8" / 15=1/2". |
Related: 4V210 (single), 4V220 (double), 4V230C/E/P (5/3 center). Add the voltage suffix when ordering.
Runs double-acting pushers and forming cylinders on packaging machines where a DC24V control cabinet drives the coils and the pressure center keeps both cylinder lines live between strokes, so the actuator sits under balanced supply during a product stoppage.
In clamping fixtures where two cylinders or a cylinder and a spring-loaded element act against each other, the pressure center feeds both sides at rest, letting the circuit find its balance without venting either line - a job a blocked or exhausted center cannot do.
Drives pick-and-place and press-fit cylinders in the 32-50 mm bore range from PLC outputs, with the terminal box wired straight into a DC24V control loop and a sub-0.05 s response keeping the station cycle tight.
Choose this 4V230P-08B-AM when your circuit needs a true pressure center: both cylinder lines stay live at rest, which suits applications where an actuator must sit under balanced supply rather than drift or bleed down. If you only need the cylinder to hold position with ports blocked, step to the closed-center 4V230C; if it should float free, the exhaust-center 4V230E fits; and if no center condition is needed, the 5/2 4V210 or 4V220 gives you Cv 1.0 and up to 5 cycles per second instead of Cv 0.8 (catalog figure for the 4V230C-08) at 3 cycles per second. Bores above about 50 mm or fast cycle rates belong on the 4V300 (Cv 1.65); very small actuators run more economically on the 4V100 (Cv 0.6).
For a like-for-like replacement, match five points: the 4V200 body, the 30P function, the 1/4 PT port and thread type (PT, G or NPT), the DC24V coil, and the terminal-box entry. Any single solenoid base or manifold plate for 4V200 valves accepts this body, so a single valve can later grow into an integrated manifold group. If your original valve was the standard-coil 4V230P-08B, this -AM version is a direct swap with the AMISCO coil already fitted.
Quick checklist
It is a 5/3-way valve for double-acting cylinders and air actuators - never single-acting types, which need a 3/2 valve. Flow is 13.6 mm2 effective area, Cv 0.8 (catalog figure for the 4V230C-08), with a maximum of 3 cycles per second, so it comfortably serves cylinders of roughly 32-50 mm bore at moderate stroke speeds. It operates on filtered air (40 um element) at 0.15-0.8 MPa.
-AM means the valve ships with an AMISCO (Italian) solenoid coil fitted instead of the standard AirTAC coil. You still order and wire it as a DC24V valve with a terminal-box entry, but the exact wattage of the AMISCO coil is not listed in our datasheet - tell us your power-budget figure when requesting a quote and we will confirm the coil rating with the factory before you commit.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.