
The AirTAC ACQ Ultra Thin Air Cylinder ACQ50X15T is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø50mm bore and 15mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ50X15T is a double-acting JIS compact cylinder engineered for space-constrained pneumatic setups. It provides a substantial 981.8 N push force at 0.5 MPa while utilizing a short C-clip and riveted body architecture that drastically reduces axial mounting depth compared to standard round-body units.
This 50mm bore variant moves a 20mm piston rod over a 15mm travel distance. Deceleration is managed by fixed NBR elastomer bumpers at both end stops rather than adjustable air cushions, meaning high-speed applications should incorporate external shock absorbers or slower approach speeds. The housing features integrated magnetic-switch grooves, though this specific configuration ships without the internal sensor magnet. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ50X15T |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø50 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Drives the folding mechanisms on packaging lines where a short 15mm stroke rapidly opens corrugated board flaps before sealing.
Holds aluminum castings securely inside machining centers, utilizing the 981.8 N extend force to resist cutting vibration.
Actuates routing flaps on conveyor systems to sort heavy product pallets, benefiting from the compact footprint to fit between tight frame rails.
When sizing your motion setup, consider stepping down to the 40mm bore (628.3 N push @0.5 MPa) for lighter loads, or moving up to the 63mm bore (1558.6 N push @0.5 MPa) if your mechanism requires greater thrust. To confirm your ordering essentials for this unit: specify the 50mm bore, 15mm stroke, NPT1/4 port, female M10x1.5 rod-end thread, and no magnet. Remember that a standard ACQ body will drift and lose its position if air pressure drops or the valve is centered; the fixed NBR bumper only softens the end stop and cannot lock the load. For fail-safe vertical holding, an external rod lock or pilot-operated check valve is necessary.
Quick checklist
The ACQ50X15T generates 981.8 N push and 824.6 N pull at 0.5 MPa, 1374.4 N push at 0.7 MPa, with a maximum push capacity of 200 kgf at 1.0 MPa. The pneumatic port size is NPT1/4.
No, the ACQ50X15T uses fixed NBR elastomer bumpers at the stroke ends to absorb impact. It is not an adjustable air cushion, so for high kinetic energy loads you should slow the approach speed or mount an external shock absorber.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.