
The AirTAC ACQ Ultra Thin Air Cylinder ACQ50X25BCBT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø50mm bore and 25mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ50X25BCBT is a double-acting JIS compact cylinder engineered for tight axial spaces, utilizing a short C-clip and riveted body design that drastically reduces mounting depth compared to round-body units. It yields 981.8 N of push force and 824.6 N of pull force at 0.5 MPa, with a NPT1/4 port driving a 20 mm piston rod.
This specific configuration includes a male M18x1.5 threaded rod end for direct load coupling and ships with a CB mounting bracket for rear clevis attachment. Deceleration is handled by fixed NBR elastomer bumpers at the stroke extremes rather than adjustable pneumatic cushions, effectively absorbing end-stop impact within the 25 mm travel. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ50X25BCBT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø50 mm |
| Stroke | 25 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Provides the 981.8 N push at 0.5 MPa required to cleanly fold and seal corrugated cardboard flaps on a continuous packaging line, utilizing the 25 mm stroke for rapid cycling.
Leverages the CB mounting bracket to pivot a routing flap, using the male M18x1.5 thread to securely anchor the linkage arm that redirects heavy wooden pallets on a chain conveyor.
Drives a 20 mm rod to seat precision bearings into housings on an automated assembly lathe, where the fixed NBR bumper absorbs the 25 mm end-stop shock without rebound.
Delivering 981.8 N push at 0.5 MPa, this 50 mm bore sits comfortably between the 40 mm bore (628.3 N push) and the 63 mm bore (1558.6 N push), allowing you to step down for lighter duty or scale up for heavier loads. The ordering essentials for this unit are a 50 mm bore, 25 mm stroke, male M18x1.5 rod thread, CB rear clevis bracket, and no sensor magnet. Keep in mind that a standard ACQ body does not maintain its position if air pressure drops or the valve is centered; the rod will drift. If your application requires fail-safe load holding on air loss, you must add an external rod lock or a pilot-operated check valve.
Quick checklist
The 50 mm bore yields 981.8 N push and 824.6 N pull at 0.5 MPa, 1374.4 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes.
It uses fixed NBR elastomer bumpers at each end to absorb shock, which are not field-adjustable, so high-speed applications may need external shock absorbers. It does not hold its load if air is lost; the piston drifts and requires an external rod lock for fail-safe positioning.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.