
The AirTAC ACQ Ultra Thin Air Cylinder ACQ50X25SBT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø50mm bore and 25mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ50X25SBT is a double-acting JIS compact cylinder engineered with a short C-clip and riveted body to minimize axial mounting depth. It yields a push force of 981.8 N and a pull force of 824.6 N at 0.5 MPa, stepping up to 1374.4 N at 0.7 MPa. The 50 mm bore features a hard-anodized inner wall and a NPT1/4 port to drive pneumatic flow.
This specific configuration includes an integrated piston magnet for AirTAC magnetic reed or electronic switches, fitting into the sensor grooves around the body. It is equipped with a male M18x1.5 thread on the Ø20 mm piston rod for direct load coupling. End-of-stroke energy is absorbed by a fixed NBR elastomer bumper, which is not field-adjustable, so high kinetic energy setups may require external shock absorption. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ50X25SBT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø50 mm |
| Stroke | 25 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Drives the folding mechanism on continuous motion case packers, using the 25 mm stroke to tuck cardboard flaps rapidly before sealing.
Pushes molded plastic parts out of small tooling cavities, leveraging the 981.8 N extend force to overcome ejection resistance.
Actuates a routing flap on a high-speed parcel conveyor, relying on the male rod end to securely attach the pivoting deflector plate.
When sizing your drive, consider the ACQ40 bore (628.3 N push at 0.5 MPa) for lighter loads, or step up to the ACQ63 bore (1558.6 N push at 0.5 MPa) if your application demands greater thrust. This 50 mm model with a 25 mm stroke offers a balanced footprint for moderate force tasks. Remember that a plain compact cylinder drifts when air pressure is lost or the valve is centered; the fixed bumper only decelerates the piston near stroke end and does not lock the load. For fail-safe position holding, an external rod lock or pilot-operated check valve is required. To order, confirm the 50 mm bore, 25 mm stroke, NPT1/4 port, built-in magnet, and male M18x1.5 rod thread.
Quick checklist
This 50 mm bore double-acting cylinder provides 981.8 N push and 824.6 N pull at 0.5 MPa, 1374.4 N push at 0.7 MPa, and a maximum push force of 200 kgf at 1.0 MPa. The operating pressure range is 0.15-1.0 MPa, with a speed range of 30-500 mm/s.
No, it uses a fixed NBR elastomer bumper at each end to absorb the stop impact. Because it is not an adjustable air cushion, you should slow the approach speed or add an external shock absorber for high-energy loads.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.