
The AirTAC ACQ Ultra Thin Air Cylinder ACQ50X50SBCBT is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø50mm bore and 50mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ50X50SBCBT is a double-acting JIS compact cylinder delivering 981.8 N of push force at 0.5 MPa and 1374.4 N at 0.7 MPa. Its short C-clip and riveted piston-to-rod body design drastically reduces axial mounting depth compared to round-body units, saving valuable machine footprint. The bore is hard-anodized for longevity, and the unit operates at speeds of 30-500 mm/s.
This specific configuration includes a built-in magnet for position sensing, a male M18x1.5 threaded rod end for direct load coupling, and a CB mounting bracket. Deceleration is handled by a fixed NBR elastomer bumper at each end. Because this is a fixed bumper rather than an adjustable air cushion, operators should slow the approach or utilize an external shock absorber for high-energy loads. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ50X50SBCBT |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø50 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Drives a 50mm stroke sealing jaw on an automated packaging line, utilizing the 981.8 N push force to securely fold and press corrugated flaps.
Actuates a routing gate on a beverage conveyor, where the male M18x1.5 rod end directly threads into the diverter arm linkage.
Provides secondary clamping pressure on a machining fixture, relying on the CB bracket to secure the body while absorbing shock via the NBR bumper.
When sizing this 50mm bore, note that stepping down to a 40mm bore drops the 0.5 MPa push force to 628.3 N, while stepping up to a 63mm bore increases it to 1558.6 N. Keep in mind that a plain ACQ body will not hold a load if air pressure is lost or the valve is centered; the piston will drift and the fixed bumper only decelerates near the stroke end. For fail-safe positioning, an external rod lock or pilot-operated check valve is required.
To order this exact unit correctly, confirm the 50mm bore, 50mm stroke, NPT1/4 port, the S magnet for reed or electronic switches, the B male M18x1.5 rod thread, and the CB clevis bracket interface.
Quick checklist
At 0.5 MPa, the push force is 981.8 N and the pull force is 824.6 N. At 0.7 MPa, the push force is 1374.4 N. The maximum push force is 200 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa, with a speed range of 30-500 mm/s.
It uses a fixed NBR elastomer bumper at each end to absorb the shock, which is not an adjustable air cushion. If your cycle runs at high speed or energy, you should slow the approach or add an external shock absorber. Additionally, it does not hold its load if air is lost; the rod drifts, so an external rod lock is needed for fail-safe holding.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.