
The AirTAC ACQ Ultra Thin Air Cylinder ACQ50X60T is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø50mm bore and 60mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ50X60T is a double-acting JIS compact cylinder engineered to deliver 981.8 N of push force and 824.6 N of pull force at 0.5 MPa. It uses a short C-clip and riveted piston-to-rod architecture that minimizes overall axial length, saving valuable machine footprint depth where a conventional round-body cylinder would not fit. The Ø20 mm piston rod features a standard female M10x1.5 thread for secure load coupling.
This 50 mm bore unit relies on a fixed NBR elastomer bumper at each end to absorb end-stop impact rather than an adjustable air cushion, so operators should slow high-speed approaches or add external shock absorbers for heavy energy loads. The aluminum body includes integrated magnetic-switch grooves around its circumference, though this specific SKU ships without the internal magnet. Operating speed spans 30-500 mm/s across a 0.15-1.0 MPa pressure range. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ50X60T |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø50 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Drives the folding mechanism on continuous packaging lines, utilizing the 981.8 N push force to snap heavy cardboard flaps into place securely at high cycling rates.
Actuates a routing gate on a 50 mm bore conveyor system to redirect heavy pallets, relying on the compact C-clip body to fit within tight transfer station clearances.
Opens and closes a safety interlock door on an automated turning center, where the fixed NBR bumper quietly arrests the 60 mm stroke without requiring hydraulic cushioning.
When sizing your application, note that stepping down to a 40 mm bore yields 628.3 N of push at 0.5 MPa, while stepping up to a 63 mm bore provides 1558.6 N. This 50 mm model strikes a middle ground with 981.8 N push, reaching 1374.4 N at 0.7 MPa and a maximum 200 kgf at 1.0 MPa. To finalize your order, confirm the 60 mm stroke, NPT1/4 port, female M10x1.5 rod end, and the absence of the sensor magnet.
Because this is a standard double-acting cylinder, it will not hold its position if air pressure drops or the valve is centered; the rod drifts and the fixed bumper only decelerates it near the stroke end. If your process requires fail-safe load holding, you must integrate an external rod lock or a pilot-operated check valve into the pneumatic circuit.
Quick checklist
This 50 mm bore cylinder provides 981.8 N push and 824.6 N pull at 0.5 MPa, 1374.4 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa. The stroke is 60 mm, well within the 100 mm maximum standard stroke for this bore.
No, the ACQ50X60T uses a fixed NBR elastomer bumper at each end rather than a field-adjustable air cushion, so for high kinetic energy loads you should slow the approach or use an external shock absorber. Additionally, it cannot hold a load on air loss; the rod drifts when pressure is removed, requiring an external rod lock for fail-safe positioning.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.