
The AirTAC ACQ Ultra Thin Air Cylinder ACQ50X70ST is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø50mm bore and 70mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ50X70ST is a double-acting JIS compact cylinder engineered for space-constrained pneumatics. It yields 981.8 N of push force and 824.6 N of pull force at 0.5 MPa. The riveted C-clip body architecture drastically reduces axial mounting depth compared to traditional round-body units.
This 50mm bore unit features a 70mm stroke and a built-in piston magnet for position sensing. The hard-anodized inner wall minimizes friction, while the fixed NBR elastomer bumper absorbs end-stop impact. It is not an adjustable air cushion, so high-energy cycles may require external shock absorption. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ50X70ST |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø50 mm |
| Stroke | 70 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Drives the folding arms on continuous-motion packaging lines where 981.8 N of extend force securely snaps corrugated board flaps into place.
Acts as a high-cycle flow control gate on roller conveyors, using the 70mm stroke to physically block advancing pallets until the upstream process clears.
Pushes finished bar material out of the spindle area, relying on the integrated magnet to trigger a solid-state switch for prompt part ejection.
When sizing this actuator, stepping down to the 40mm bore provides 628.3 N of push at 0.5 MPa, while stepping up to the 63mm bore yields 1558.6 N. The ACQ50X70ST configuration specifies a 50mm bore, 70mm stroke, NPT1/4 port, female M10x1.5 rod thread, and the -S magnet option. Note that a standard compact body does not hold a load if air pressure drops; the piston drifts and an external rod lock or pilot-operated check valve is required for fail-safe position holding.
Quick checklist
At 0.5 MPa it generates 981.8 N push and 824.6 N pull, reaching 1374.4 N push at 0.7 MPa, with a maximum push capacity of 200 kgf at 1.0 MPa. The maximum standard stroke available for this 50mm bore is 100mm.
It uses a fixed NBR elastomer bumper at each end to decelerate the piston, which is not a field-adjustable air cushion. Additionally, it does not hold its load if air is lost; the rod drifts, so an external rod lock is needed for fail-safe holding.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.