
The AirTAC ACQ Ultra Thin Air Cylinder ACQ50X75ST is a genuine double-acting COMPACT (thin) air cylinder built to JIS dimensions, with a Ø50mm bore and 75mm stroke, PT1/4 air ports and a C-clip / riveted short body that saves mounting depth. Magnetic-switch slots around the body accept position sensors.
The AirTAC ACQ50X75ST is a double-acting JIS compact air cylinder engineered to save axial mounting depth in tight machinery layouts. Its short C-clip and riveted body design yields a 75 mm stroke while producing 981.8 N of push force and 824.6 N of pull force at 0.5 MPa. The aluminum body incorporates a hard-anodized inner wall to reduce friction and extend seal life.
Equipped with the -S option, this unit contains a built-in piston magnet for non-contact position sensing. Grooves around the cylinder body accept AirTAC magnetic reed or electronic solid-state switches to confirm end-of-stroke travel. Deceleration at the end caps is handled by fixed NBR elastomer bumpers rather than adjustable pneumatic cushions, so high energy cycles may require external shock absorption. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac ACQ Ultra Thin Air Cylinder ACQ50X75ST |
|---|---|
| Series | ACQ JIS compact (thin) cylinder |
| Bore size | Ø50 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod end thread | M10×1.5 female / M18×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACQ JIS compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard); G and NPT available. Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| ACQ | JIS compact (thin) double-acting cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard (G / NPT available). Related ACQ-family variants: ASQ (single-acting push), ATQ (single-acting pull), ACQD (double rod), ACQJ (adjustable stroke), TACQ (guided / non-rotating).
Actuates a routing flap on a high-speed logistics conveyor to push parcels into specific sorting lanes using 981.8 N of extend force.
Opens and closes a sliding machine safety guard within a compact footprint, using the integrated magnet to signal the controller when the door is fully closed.
Stages corrugated cardboard sheets into a palletizing robotic cell, utilizing the 75 mm stroke to index materials into the pickup zone.
This 50 mm bore generates 981.8 N of thrust at 0.5 MPa. If your payload is lighter, stepping down to the 40 mm bore yields 628.3 N of push force, whereas moving up to the 63 mm bore provides 1558.6 N for heavier lifting. Keep in mind that a standard ACQ body will drift and drop its load if air pressure is lost or the directional valve is centered, as the fixed bumper only decelerates the piston near stroke end and does not act as a locking brake. For fail-safe vertical holding, an external rod lock or pilot-operated check valve is required.
When requesting pricing, confirm the 50 mm bore, 75 mm stroke, NPT1/4 port size, integrated magnet (S option), and the default female M10x1.5 rod-end thread to ensure you receive the exact configuration needed.
Quick checklist
At 0.5 MPa, the push force is 981.8 N and the pull force is 824.6 N. At 0.7 MPa, the push force reaches 1374.4 N. The maximum push force is 200 kgf at 1.0 MPa. The operating pressure range is 0.15-1.0 MPa, with an operating speed of 30-500 mm/s.
No, the ACQ50X75ST uses fixed NBR elastomer bumpers at each end to absorb impact rather than field-adjustable pneumatic cushions. For high-speed or heavy moving loads, you should slow the approach speed or add an external shock absorber to prevent premature wear.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.