
The AirTAC GAFR Adjustable Filter Regulator GAFR30015ALJWTK is a genuine two-in-one filter & regulator — a diversion-type water/particulate filter and a balanced pressure regulator built into ONE body. It has 1/2" ports, a 5 µm filter element and regulates 0.15 - 0.4 MPa (20 - 58 psi). It has no lubricator, so it adds no oil to the airflow.
The GAFR30015ALJWTK is a filter and regulator combined into a single body, so one compact unit handles both air preparation and pressure control. With a 1/2in port and a 500 g mass, this GAFR300 body suits medium-flow lines where a smaller 1/4in unit would restrict the supply.
This version regulates from 0.15 to 0.4 MPa (20-58 psi) and uses a 5 um element for finer filtration. The automatic drain clears condensate without manual attention, and the circular gauge with MPa/psi scale lets operators read the set pressure directly. A reverse-flow valve is fitted as an ordering option. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac GAFR Adjustable Filter Regulator GAFR30015ALJWTK |
|---|---|
| Series | GAFR300 filter & regulator |
| Port size | 1/2" (NPT thread) |
| Filtering grade | 5 µm |
| Pressure range | 0.15 - 0.4 MPa (20 - 58 psi) |
| Type | Lower pressure |
| Bowl material | PC |
| Drain type | Automatic drain |
| Fluid | Air |
|---|---|
| Max. pressure | 1.0 MPa (145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Capacity of drain bowl | 60 cc |
| Bracket | Not included (J) |
| Weight | 500 g |
Specifications follow the official AirTAC GAFR catalogue (pages 235-236). Air must not freeze in the unit. The fitted circular gauge reads in psi / bar, set by the NPT thread code. This unit filters and regulates only; it does not add lubrication.
| GAFR300 | GA300 series filter & regulator — sets the port range, drain-bowl capacity and weight. |
|---|---|
| (blank) | Bowl material: PC. Available on this body: PC (blank), Metal (C), Nylon (N). |
| 15 | Port size 1/2". This body offers 08 = 1/4", 10 = 3/8", 15 = 1/2". |
| A | Drain: Automatic drain. |
| L | Lower pressure type — 0.15 - 0.4 MPa (20 - 58 psi). This body offers Standard (S) or Lower pressure (L). |
| J | No bracket (J) — supplied without the mounting bracket. |
| (blank) | Circular pressure gauge fitted. |
| W | Filtering grade 5 µm. |
| T | NPT thread; gauge scale psi / bar. |
| K | Reverse-flow (reflux) valve attached. |
The filter and the regulator are ONE body here — there is no separate GAF filter or GAR regulator part to assemble. Need lubrication downstream too? Add a lubricator by ordering the matching GAFC300-15 F.R.L. combination instead.
Figures are the end of the flow curve plotted in the AirTAC catalogue at 0.7 MPa inlet pressure — a sizing envelope for comparing bodies, not a rated flow. Read the catalogue curve for a real duty point. Outlet pressure falls as flow rises, so size a body with headroom above your peak demand.
| This model | GAFR300 · 1/2" · curve to 3500 L/min |
|---|---|
| One size down | GAFR200 |
| One size up | GAFR400 (curve to 7000 L/min) |
| Add a lubricator | GAFC300-15 (F.R.L. combination) |
Feed a bank of precision pneumatic valves that need clean, regulated air at a consistent lower pressure. The 5 um element protects fine internal passages from particle wear.
Supply a machine tool's air-operated coolant pump where a lower pressure setting prevents over-spray. The automatic drain keeps condensate from reaching the pump when lines run wet.
Provide a stable lower-pressure air source for a calibration or test bench. The balanced regulator holds the set point as shop supply varies, and the gauge confirms the reading.
Choose GAFR300 for flows up to 3500 L/min at 0.7 MPa inlet, stepping up from the GAFR200's 2000 L/min envelope if your line needs more capacity. The PC bowl suits general industrial use, while the automatic drain (A) handles unattended or wet lines. The L type tops out at 0.4 MPa, so verify your system never needs more than that. The J code means no bracket is included, so plan for panel mounting or an existing support. The 5 um element traps finer particles than the standard 40 um, but requires more frequent service. The NPT thread gives an MPa/psi gauge scale. If oil is needed downstream, order the matching GAFC300-15 combination instead. With a 1.0 MPa max supply, you have about 0.6 MPa of headroom above the 0.4 MPa top of this unit's regulated range.
Quick checklist
This is a filter and regulator only — it delivers filtered, pressure-set air with no added oil. If a downstream tool needs lubrication, add a separate lubricator or order the GAFC300-15 combination; do not expect an oil mist from this unit.
Working pressure range is 0.15-0.4 MPa (20-58 psi). Maximum pressure is 1.0 MPa (145 psi) and proof pressure is 1.5 MPa (215 psi). Temperature range is -5 to 70 C. The drain bowl holds 60 cc and the unit weighs 500 g. It has a 1/2in port, 5 um element, automatic drain, and a fitted gauge.
The K indicates a reverse-flow (reflux) valve is fitted to the unit. It is an ordering difference from the standard version. The catalogue does not specify its function in our data, so treat it as a specified option for your application.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, availability and lead time — usually within 7 hours.