
The AirTAC GC200-06 FRL Unit (GC20006MNT) is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT1/8" ports, a 40 µm element, a manual drain and regulates 0.05 - 0.9 MPa (7 - 130 psi).
The GC series is AirTAC's three-unit F.R.L. combination: a separate air filter, a pressure regulator and an oil-mist lubricator, each doing its own job on the same compressed-air line. This GC20006MNT is the size 200 set with NPT1/8 in. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. With the manual drain, the regulator setting range is 0.05-0.9 MPa (7-130 psi).
This is a genuine AirTAC part for compressed air, rated up to 1.0 MPa (145 psi) working pressure and -5 to 70 C. The G series is offered in sizes 200, 300, 400 and 600 with ports from 1/8 to 1 in., plus drain, filter-grade, gauge, reverse-valve and thread (NPT on this code) options. Flow is published as curves rather than a single rating, so ask us to confirm datasheet figures for your application on request.
| Model | AirTAC GC200-06 FRL Unit (GC20006MNT) |
|---|---|
| Series | GC200 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT1/8" (NPT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.05 - 0.9 MPa (7 - 130 psi) |
| Pressure type | Standard type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Manual drain |
| Bowl material | PC |
| Pressure gauge | Not fitted |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.05 - 0.9 MPa (7 - 130 psi). The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC200 | G-series F.R.L. combination, 200 body — sets the port range. |
|---|---|
| 06 | Port size PT1/8". This body offers 06 = PT1/8", 08 = PT1/4". |
| M | Drain: Manual drain — this also sets the regulating band (0.05 - 0.9 MPa (7 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| N | No pressure gauge (N). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| T | NPT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF200-06 filter, GR200-06 regulator and GL200-06 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC200 · PT1/8" · 40 µm |
|---|---|
| One size up | GC300 |
| Two-unit equivalent | GFC200-06 |
| Build order | Filter → regulator → lubricator |
Conditions the air feeding a small bench-mounted pneumatic press, with filtered, regulated and lubricated air at one manual-drain point the operator services during setup.
Supplies a paint spray gun on a workshop prep bench, filtering out water and particulate at 40 um, holding a steady gun pressure and carrying oil mist for the gun trigger and needle.
Runs the small cylinders on a manual-load carton taping machine, keeping water and dirt out of the valves so the tape head cycles cleanly through each box.
Size 200 with 1/8 in. ports is the smallest step in the G series - step up to GC300/400/600 as your port size or air demand grows. The manual drain suits units mounted where someone can drain the bowl on a routine; pick the automatic (A) or differential-pressure (default) variant for hard-to-reach spots. The standard element is 40 um; the W suffix gives a 5 um element for finer protection. This variant has no gauge (N); gauge versions can be ordered with MPa, psi or bar scales. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. Flow is published as curves, not a single rated figure, so let us confirm sizing against the datasheet before you order.
Quick checklist
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR200-06 regulator with a GF200-06 filter on that branch.
Flow for the G series is published as curves, not a single rated figure, so we do not quote a number here. Send us your line pressure, downstream demand and acceptable pressure drop, and we will confirm sizing against the AirTAC datasheet before you order.
A GFR filters and regulates in one body but does not lubricate. The GC adds a separate lubricator, so the downstream air carries an oil mist for air tools and cylinders that need it. If your actuators are pre-lubricated or oil-free by design, the two-unit GFC or the GFR alone is the leaner choice; if you run classic air tools, the three-piece GC keeps the oil feed separate from the filter and regulator.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7 hours.