
The AirTAC GC300-08 FRL Unit (GC30008AC3WT) is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT1/4" ports, a 5 µm element, a automatic drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
GC30008AC3WT is a three-unit AirTAC G-series F.R.L. combination: a separate air filter, pressure regulator and lubricator supplied as one matched set for 1/4 in (NPT1/4) ports. This configuration pairs an automatic-drain bowl with 5 um filtration and an external round pressure gauge scaled in bar, so condensate is expelled from the bowl without manual attention, fine particles are stripped ahead of regulation, and metered oil mist protects downstream equipment.
This is a genuine AirTAC part. The G series is offered in 200, 300, 400 and 600 sizes, carries compressed air only, is rated for up to 1.0 MPa (145 psi) working pressure and -5 to 70 C, and uses polycarbonate bowls at the 300 size. AirTAC publishes flow as characteristic curves rather than a single rating, so we confirm flow and any other datasheet figure on request. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | AirTAC GC300-08 FRL Unit (GC30008AC3WT) |
|---|---|
| Series | GC300 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT1/4" (NPT thread) |
| Filtering grade | 5 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Standard type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Automatic drain |
| Bowl material | PC |
| Pressure gauge | Fitted — round, bar scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.15 - 0.9 MPa (20 - 130 psi). The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC300 | G-series F.R.L. combination, 300 body — sets the port range. |
|---|---|
| 08 | Port size PT1/4". This body offers 08 = PT1/4", 10 = PT3/8", 15 = PT1/2". |
| A | Drain: Automatic drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| C | Gauge shape: Round. C is round, F is square. |
| 3 | Gauge scale: bar. 1 is MPa, 2 is psi, 3 is bar. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| T | NPT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF300-08 filter, GR300-08 regulator and GL300-08 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC300 · PT1/4" · 5 µm |
|---|---|
| One size down | GC200 |
| One size up | GC400 |
| Two-unit equivalent | GFC300-08 |
| Build order | Filter → regulator → lubricator |
Filtered, regulated and lubricated air keeps gripper cylinders cycling cleanly on assembly cells, and the automatic drain suits unattended shifts where nobody bleeds the bowl by hand.
The set feeds the flap-fold and sealing cylinders on a cartoner, holding a steady regulator setting through the shift while the 5 um element keeps fine debris out of close-tolerance valves.
Torque drivers and nutrunners run best on clean, oiled air; this unit conditions the bench drop, with the round bar-scale gauge letting operators verify line pressure at a glance.
The 300 size with 1/4 in ports sits in the middle of the G range; step down to 200 or up to 400/600 according to the flow your line needs. Drain choices are automatic (this model), manual, or the differential-pressure default, and the filter element is 40 um standard or 5 um (W) as coded here. With an automatic drain, the regulator adjusts across 0.15-0.9 MPa (20-130 psi). The gauge on this code is an external round unit scaled in bar; This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. Because flow is published as curves rather than a single rating, ask us to confirm sizing against your application before ordering.
Quick checklist
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR300-08 regulator with a GF300-08 filter on that branch.
AirTAC publishes G-series flow as characteristic curves rather than a single rated figure, so no one-number rating applies here. Send us your required flow and operating pressure and we will confirm suitability against the datasheet curves on request before you order.
Yes. The GC family is offered with automatic (A), manual (M) or the differential-pressure default drain, and with the 40 um standard element or the 5 um W option. Note the regulator range differs by drain: 0.15-0.9 MPa (20-130 psi) for automatic and differential-pressure drains versus 0.05-0.9 MPa (7-130 psi) for manual.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7 hours.