
The AirTAC GC300-08 FRL Unit (GC30008MNTK) is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT1/4" ports, a 40 µm element, a manual drain and regulates 0.05 - 0.9 MPa (7 - 130 psi).
The GC30008MNTK is a genuine AirTAC three-piece F.R.L. combination - separate filter, regulator and lubricator - with a reverse/check valve (K) fitted, so downstream pressure is held if the upstream supply dips. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. The regulator is the standard type and no pressure gauge is fitted (N code). Maximum working pressure is 1.0 MPa (145 psi), operating range -5 to 70 C, non-freezing; at size 300 the filter and lubricator bowls are PC (polycarbonate).
The G-series covers sizes 200, 300, 400 and 600 with ports from 1/8 to 1 inch, drain choices (differential-pressure, automatic or manual), 40 um or 5 um (W) filtration, gauge options and the reverse/check valve (K) shown here. Flow is published as curves rather than a single rated figure, so we confirm the datasheet and flow curves for the GC30008MNTK on request.
| Model | AirTAC GC300-08 FRL Unit (GC30008MNTK) |
|---|---|
| Series | GC300 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT1/4" (NPT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.05 - 0.9 MPa (7 - 130 psi) |
| Pressure type | Standard type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Manual drain |
| Bowl material | PC |
| Pressure gauge | Not fitted |
| Reflux valve | Fitted (reverse flow permitted) |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.05 - 0.9 MPa (7 - 130 psi). The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC300 | G-series F.R.L. combination, 300 body — sets the port range. |
|---|---|
| 08 | Port size PT1/4". This body offers 08 = PT1/4", 10 = PT3/8", 15 = PT1/2". |
| M | Drain: Manual drain — this also sets the regulating band (0.05 - 0.9 MPa (7 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| N | No pressure gauge (N). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| T | NPT thread. PT is the default; G is BSPP and T is NPT. |
| K | Reverse-flow (reflux) valve fitted. |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF300-08 filter, GR300-08 regulator and GL300-08 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC300 · PT1/4" · 40 µm |
|---|---|
| One size down | GC200 |
| One size up | GC400 |
| Two-unit equivalent | GFC300-08 |
| Build order | Filter → regulator → lubricator |
Conditions air feeding a pneumatic assembly press; the reverse/check valve keeps the press circuit charged if the shop supply sags mid-cycle, protecting the clamping sequence.
Prep air for weld-cell valve manifolds and gripper circuits, where a supply dip between weld sequences must not collapse settings on downstream tooling.
Supplies clean, regulated, lubricated pilot air to large process control valves, with the check valve holding pilot pressure steady through compressor unload events.
Match the size and port step (200 to 600, 1/8 to 1 inch) to your circuit's air demand; this 300 size carries a NPT1/4 port. This unit has manual drain (M) - pick automatic (A) or differential-pressure (default) if bowls will not be drained on schedule. Regulation range for this manual-drain set is 0.05-0.9 MPa (7-130 psi). The K code adds a reverse/check valve, useful where an intermittent supply or upstream drop-off must not dump downstream pressure. Filtration is 40 um standard; W gives 5 um. No gauge is fitted (N code); square embedded or external round gauges with MPa, psi or bar scales are options. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. Flow appears only as curves, not a single rating - ask us to confirm sizing against your application before ordering.
Quick checklist
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR300-08 regulator with a GF300-08 filter on that branch.
AirTAC publishes G-series flow as curves, not as a single rated figure, so we do not state a number. Tell us your machine's air demand and line pressure, and we will confirm the GC30008MNTK datasheet and flow curve on request and check whether size 300 at NPT1/4 is the right step.
K means a reverse/check valve is fitted in the set. If upstream pressure falls below the regulated downstream pressure, the check valve prevents backflow, holding the downstream circuit at its set pressure. The otherwise identical GC30008MN does not carry the valve.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7 hours.