
The AirTAC MBL Aluminum Alloy Mini Cylinder MBL20X15SCAT is a genuine double-acting aluminum-barrel mini round cylinder with a Ø20mm bore and 15mm stroke, 1/8" air ports and a fixed rubber bumper. Its compact riveted body suits push, hold and clamp motion in tight machine spaces.
The AirTAC MBL20X15SCAT is a compact double-acting aluminum mini round cylinder engineered for tight machine spaces. At 20mm bore and a short 15mm stroke, it generates 157N push and 132N pull force at 0.5 MPa. The CA pivot back cover allows the cylinder body to swing on a pin, making it ideal for arcing or angular load applications where a rigid flat-end mount would bind. An integrated magnet (-S) enables position detection.
Unlike ISO tie-rod bodies, this cylinder utilizes a riveted rolling-packed aluminum barrel that crimps the covers directly to the tube for minimal weight. The 8mm carbon-steel piston rod features 20µm hard-chrome plating for wear resistance, while a heterogeneous two-way piston seal retains grease for extended operational life. End-of-stroke deceleration relies on a fixed rubber bumper, not an adjustable cushion. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac MBL Aluminum Alloy Mini Cylinder MBL20X15SCAT |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder |
| Bore size | Ø20 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Rubber bumper (MBLC variant: adjustable air cushion) |
| Max stroke | Up to 500 mm |
Specifications follow the official AirTAC MBL series datasheet. Confirm against the product label before installation. Standard stroke to 500 mm (special order to 800 mm). Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | — |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| MBL | Aluminum-barrel mini round cylinder, double acting. |
|---|---|
| 20 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: MBLC (adjustable cushion), MBLD (double rod), MBLJ (adjustable stroke), MSBL/MTBL (single acting).
Drives small robotic gripper jaws in electronics assembly, using the 15mm stroke to snap parts into PCB sockets with precise 157N force.
Pivots a test probe arm down onto microchips, leveraging the CA clevis mount to accommodate slight angular misalignment during high-speed cycling.
Tucks small packaging flaps on a compact filling line, where the short 15mm stroke and lightweight aluminum body fit within tight guide rails.
If your application requires less force, no smaller standard MBL bore exists below 20mm, so you would look outside this mini series. Stepping up to the 25mm bore increases output to 245N push at 0.5 MPa. For higher kinetic energy or faster cycling, the MBLC variant offers an adjustable air cushion to absorb impact. If you need push-only or pull-only operation without continuous air, consider the MSBL or MTBL single-acting variants.
This CA pivot configuration suits angular linkages, but remember the fixed rubber bumper only softens end-of-stroke impact; it is not a locking device. The rod will drift if air pressure is lost. Because the 15mm stroke is very short, side-load bending is negligible, but always ensure the pivot pin is aligned to prevent seal wear. Port size is G1/8 with a default NPT tapered thread.
Quick checklist
This 20mm bore cylinder provides 157N push and 132N pull at 0.5 MPa, 220N push at 0.7 MPa, and a maximum theoretical force of 32 kgf at 1.0 MPa. It uses an 8mm carbon-steel rod with an M8x1.25 rod-end thread.
The base MBL uses a fixed rubber bumper that cannot be adjusted; for adjustable air cushioning, you must specify the MBLC variant. This S-suffix model includes a magnet and accepts AirTAC CMSG (reed), DMSG, or EMSG (electronic solid-state) sensor switches for position detection.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.