
The AirTAC MBL Aluminum Alloy Mini Cylinder MBL20X200UT is a genuine double-acting aluminum-barrel mini round cylinder with a Ø20mm bore and 200mm stroke, 1/8" air ports and a fixed rubber bumper. Its compact riveted body suits push, hold and clamp motion in tight machine spaces.
The AirTAC MBL20X200UT is a compact double-acting aluminum mini round cylinder engineered for tight machine spaces. Operating at 0.5 MPa, it provides 157 N of push force and 132 N of pull force across its 200 mm stroke, making it well-suited for lightweight positioning tasks. The U suffix denotes a rigid flat-end rear cover for straightforward fixed mounting.
Unlike tie-rod bodies, this cylinder uses a riveted rolling-packed barrel where the covers are crimped to the tube, creating a lightweight, permanently sealed assembly that is not designed to be disassembled. It relies on a fixed rubber bumper to soften end-of-stroke impacts rather than an adjustable air cushion. Note that because this specific SKU lacks the -S magnet suffix, it cannot accommodate a CMSG, DMSG, or EMSG sensor switch for rod position detection. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac MBL Aluminum Alloy Mini Cylinder MBL20X200UT |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder |
| Bore size | Ø20 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Rubber bumper (MBLC variant: adjustable air cushion) |
| Max stroke | Up to 500 mm |
Specifications follow the official AirTAC MBL series datasheet. Confirm against the product label before installation. Standard stroke to 500 mm (special order to 800 mm). Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | — |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| MBL | Aluminum-barrel mini round cylinder, double acting. |
|---|---|
| 20 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: MBLC (adjustable cushion), MBLD (double rod), MBLJ (adjustable stroke), MSBL/MTBL (single acting).
Pushes severed circuit boards out of the routing fixture with 157 N of force, fitting easily into cramped electronics assembly machinery.
Provides the 200 mm reach needed to press IC sockets into PCBs, relying on the rigid U flat-end cover to maintain alignment in tight enclosures.
Actuates a small sorting flap to redirect lightweight plastic caps on a packaging line, where the compact 20 mm profile saves valuable deck space.
With a 200 mm stroke on an Ø8 mm rod, this mini cylinder is highly susceptible to side-load bending; an external guide or a pivot mounting accessory is strongly recommended to prevent rod bearing damage. If your application requires less travel, stepping down to the 20 mm bore with a 150 mm stroke reduces the unsupported length, while stepping up to a 32 mm bore yields 402 N of push force at 0.5 MPa for heavier loads. The base MBL uses a fixed rubber bumper, so if your payload requires deceleration control at higher speeds, consider the MBLC variant with adjustable air cushion. Keep in mind that a standard rubber bumper only softens impact; it does not hold the load if air pressure is lost, so a separate pilot-operated check valve is needed for position holding. This SKU features a G1/8 port, NPT thread form, and a U flat-end back cover.
Quick checklist
At 0.5 MPa, this double-acting cylinder outputs 157 N of push force and 132 N of pull force. At 0.7 MPa, the push force increases to 220 N, with a theoretical maximum of 32 kgf at 1.0 MPa. It operates on filtered air at 0.15-1.0 MPa, runs at speeds of 30-800 mm/s, and uses a G1/8 port with an M8x1.25 rod-end thread.
Because this specific SKU lacks the -S suffix, it has no built-in magnet and cannot accept CMSG, DMSG, or EMSG electronic or reed sensor switches. Additionally, the base MBL relies on a fixed rubber bumper to absorb end-of-stroke impact; for adjustable air cushioning, you must upgrade to the MBLC variant.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.