
The AirTAC MBL Aluminum Alloy Mini Cylinder MBL20X30SUT is a genuine double-acting aluminum-barrel mini round cylinder with a Ø20mm bore and 30mm stroke, 1/8" air ports and a fixed rubber bumper. Its compact riveted body suits push, hold and clamp motion in tight machine spaces.
The AirTAC MBL20X30SUT is a genuine double-acting aluminum mini round cylinder engineered for extremely tight machine spaces. Operating at 0.5 MPa, it yields 157 N of push force and 132 N of pull force over a short 30 mm stroke. The riveted rolling-packed barrel permanently crimps the front and rear covers to the tube, yielding a featherlight body that is not designed to be disassembled like a heavy tie-rod cylinder.
This specific SKU includes the U flat-end back cover for rigid fixed mounting and the -S built-in magnet for position detection. Without a live air signal, the rod will drift, as the internal fixed rubber bumper only softens end-of-stroke impact rather than locking the load. The 8 mm carbon-steel rod features 20 um hard-chrome plating to resist wear, while the heterogeneous two-way piston seal retains grease for a long service life. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac MBL Aluminum Alloy Mini Cylinder MBL20X30SUT |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder |
| Bore size | Ø20 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Rubber bumper (MBLC variant: adjustable air cushion) |
| Max stroke | Up to 500 mm |
Specifications follow the official AirTAC MBL series datasheet. Confirm against the product label before installation. Standard stroke to 500 mm (special order to 800 mm). Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | — |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| MBL | Aluminum-barrel mini round cylinder, double acting. |
|---|---|
| 20 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: MBLC (adjustable cushion), MBLD (double rod), MBLJ (adjustable stroke), MSBL/MTBL (single acting).
Provides 157 N of push at 0.5 MPa to gently eject populated printed circuit boards from test fixtures without damaging delicate solder joints.
The short 30 mm stroke and lightweight aluminum body fit perfectly within compact packaging lanes to fold small pharmaceutical carton flaps.
Uses the -S magnet with a DMSG electronic sensor to verify the precise opening of 96-well microplate lids inside crowded laboratory automation.
At the smallest standard bore in the MBL range, stepping up to the MBL25X30 provides a higher 245 N push force at 0.5 MPa if your fixture exceeds the 20 mm capacity. Conversely, if the 157 N output is excessive for a delicate task, you would drop out of the mini round family to a smaller body. Because this is a 30 mm stroke, side-load bending is minimal, but the 8 mm rod still has low tolerance for offset loads.
This exact replacement matches a 20 mm bore, 30 mm stroke, G1/8 port size with default NPT tapered threads, a U flat-end back cover, and a built-in -S magnet. If your cycle requires end-position cushioning rather than the standard fixed rubber bumper, select the MBLC20 variant for its adjustable air cushion.
Quick checklist
The 20 mm bore generates 157 N push and 132 N pull at 0.5 MPa, 220 N push at 0.7 MPa, and a maximum theoretical force of 32 kgf at 1.0 MPa. It operates at a speed of 30-800 mm/s.
The base MBL uses a fixed rubber bumper that cannot be adjusted; for adjustable air cushioning, you need the MBLC variant. This SKU includes the -S magnet, allowing you to mount CMSG reed or DMSG/EMSG electronic switches for rod position detection.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.