
The AirTAC MBL Aluminum Alloy Mini Cylinder MBL20X450-CAT is a genuine double-acting aluminum-barrel mini round cylinder with a Ø20mm bore and 450mm stroke, 1/8" air ports and a fixed rubber bumper. Its compact riveted body suits push, hold and clamp motion in tight machine spaces.
The AirTAC MBL20X450-CAT is a compact double-acting aluminum mini round cylinder engineered for tight machine spaces. It delivers 157 N of push force and 132 N of pull force at 0.5 MPa, making it suited for moving light loads over a 450 mm travel. The riveted rolling-packed barrel permanently crimps the front and rear covers to the tube, yielding a light body that is not designed to be disassembled like a tie-rod cylinder.
This SKU features a CA pivot back cover that swings on a pin to accommodate arcing or angular loads during the stroke. Because it lacks the -S suffix, a position sensor cannot be fitted to this cylinder. The internal end-of-stroke deceleration relies on a fixed rubber bumper, not an adjustable cushion screw. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac MBL Aluminum Alloy Mini Cylinder MBL20X450-CAT |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder |
| Bore size | Ø20 mm |
| Stroke | 450 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Rubber bumper (MBLC variant: adjustable air cushion) |
| Max stroke | Up to 500 mm |
Specifications follow the official AirTAC MBL series datasheet. Confirm against the product label before installation. Standard stroke to 500 mm (special order to 800 mm). Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | — |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| MBL | Aluminum-barrel mini round cylinder, double acting. |
|---|---|
| 20 | Bore size in mm. |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: MBLC (adjustable cushion), MBLD (double rod), MBLJ (adjustable stroke), MSBL/MTBL (single acting).
Pivots a lightweight flap on a packaging line to deflect small cardboard cartons, utilizing the CA pivot cover to handle the arcing motion across the 450 mm stroke.
Traverses a delicate thread guide carriage back and forth 450 mm, where the 157 N push force at 0.5 MPa is sufficient to overcome friction without snapping the fiber.
Advances a low-friction pusher plate to nudge lightweight plastic film rolls into a staging area, fitting easily into the machine's narrow frame.
For lighter or heavier duties, step down to the 20 mm bore or up to the 25 mm bore, which provides 245 N push at 0.5 MPa. If your cycle requires end-of-stroke velocity control for heavier moving masses, select the MBLC variant for its adjustable air cushion. Note that the fixed rubber bumper only softens end impact and does not lock the rod; if pressure is lost, the load will drift, requiring an external rod lock or pilot-operated check valve to hold position.
At a 450 mm stroke, the Ø8 mm piston rod is highly susceptible to bending under side loads. The CA clevis back cover on this unit helps absorb angular misalignment, but for strict linear guidance over this long travel, you should use an external guide rail or switch to the MBLD double-rod cylinder to prevent rod bearing wear.
Quick checklist
This 20 mm bore cylinder provides 157 N push and 132 N pull at 0.5 MPa, 220 N push at 0.7 MPa, and a maximum theoretical force of 32 kgf at 1.0 MPa. It has a G1/8 port, an Ø8 mm rod with an M8x1.25 thread, and operates at speeds of 30-800 mm/s.
No. Because the model code lacks the -S suffix, it has no internal magnet and cannot accept CMSG, DMSG, or EMSG electronic sensor switches. Additionally, the base MBL uses a fixed rubber bumper for end-of-stroke impact absorption; for adjustable air cushioning, you must specify the MBLC variant.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.