
The AirTAC MBL Aluminum Alloy Mini Cylinder MBL25X15SCAT is a genuine double-acting aluminum-barrel mini round cylinder with a Ø25mm bore and 15mm stroke, 1/8" air ports and a fixed rubber bumper. Its compact riveted body suits push, hold and clamp motion in tight machine spaces.
The AirTAC MBL25X15SCAT is a compact double-acting aluminum mini round cylinder engineered for tight machine spaces. Operating at 0.5 MPa, it yields 245 N of push force and 206 N of pull force across its 15 mm stroke. The riveted rolling-packed barrel crimps the front and rear covers directly to the tube, yielding a lightweight body that is not designed to be disassembled like a standard tie-rod cylinder.
This specific SKU features a CA pivot back cover, allowing the cylinder body to swing on a pin to accommodate arcing or angular loads. The -S suffix denotes a built-in magnet for use with CMSG, DMSG, or EMSG sensor switches to track rod position. The Ø10 mm carbon-steel piston rod features 20 µm hard-chrome plating, and the heterogeneous two-way piston seal retains grease for extended operational life. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac MBL Aluminum Alloy Mini Cylinder MBL25X15SCAT |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder |
| Bore size | Ø25 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Rubber bumper (MBLC variant: adjustable air cushion) |
| Max stroke | Up to 500 mm |
Specifications follow the official AirTAC MBL series datasheet. Confirm against the product label before installation. Standard stroke to 500 mm (special order to 800 mm). Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | — |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| MBL | Aluminum-barrel mini round cylinder, double acting. |
|---|---|
| 25 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: MBLC (adjustable cushion), MBLD (double rod), MBLJ (adjustable stroke), MSBL/MTBL (single acting).
Provides 245 N of push at 0.5 MPa to hold printed circuit boards firmly against a machining fixture during high-speed routing operations.
Drives the short 15 mm stroke on vertical form-fill-seal packaging equipment to close and crimp polymer film pouches with precise timing.
Utilizes the CA pivot back cover to swing a thread guide arm into position on a weaving loom, accommodating the angular arc of the mechanism.
When sizing this 25 mm bore actuator, stepping down to the 20 mm bore reduces push force to 157 N at 0.5 MPa, while stepping up to the 32 mm bore increases it to 402 N. The 15 mm stroke is ideal for short, rapid clamping motions. Because the base MBL uses a fixed rubber bumper rather than an adjustable air cushion, select the MBLC variant if your application requires precise end-of-stroke deceleration for heavier moving masses.
Note that the standard MBL does not hold its position if air pressure is lost or the valve is centered; the rod will drift. For load-holding requirements, utilize an external rod lock or pilot-operated check valve. Replacement must match the 25 mm bore, 15 mm stroke, G1/8 port, NPT thread form, CA pivot back cover, and the built-in magnet.
Quick checklist
At 0.5 MPa, this 25 mm bore cylinder provides 245 N push and 206 N pull force. At 0.7 MPa, push force is 343 N. The maximum theoretical force is 50 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa, with a speed of 30-800 mm/s.
No, the base MBL features a fixed rubber bumper to soften end-of-stroke impact, not an adjustable cushion screw. If you need adjustable air cushioning for faster speeds or heavier loads, you must select the MBLC variant.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.