
The AirTAC MBL Aluminum Alloy Mini Cylinder MBL25X200SUT is a genuine double-acting aluminum-barrel mini round cylinder with a Ø25mm bore and 200mm stroke, 1/8" air ports and a fixed rubber bumper. Its compact riveted body suits push, hold and clamp motion in tight machine spaces.
The AirTAC MBL25X200SUT is a compact double-acting aluminum mini round cylinder engineered for tight machine spaces. It provides 245 N push and 206 N pull force at 0.5 MPa from a 25 mm bore and 200 mm stroke. The U flat-end back cover provides a rigid fixed rear mounting face. An integrated -S magnet allows CMSG, DMSG, or EMSG electronic sensor switches to track rod position for end-of-stroke signaling.
Unlike tie-rod bodies, the MBL uses a riveted rolling-packed aluminum barrel with crimped front and back covers, keeping weight low but making the cylinder non-rebuildable. A heterogeneous two-way piston seal retains grease for long service life, while the carbon steel rod features 20 µm hard-chrome plating for wear and corrosion resistance. End-of-stroke impact is absorbed by a fixed rubber bumper, not an adjustable cushion. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac MBL Aluminum Alloy Mini Cylinder MBL25X200SUT |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder |
| Bore size | Ø25 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Rubber bumper (MBLC variant: adjustable air cushion) |
| Max stroke | Up to 500 mm |
Specifications follow the official AirTAC MBL series datasheet. Confirm against the product label before installation. Standard stroke to 500 mm (special order to 800 mm). Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | — |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| MBL | Aluminum-barrel mini round cylinder, double acting. |
|---|---|
| 25 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: MBLC (adjustable cushion), MBLD (double rod), MBLJ (adjustable stroke), MSBL/MTBL (single acting).
Uses the 245 N push force at 0.5 MPa to deflect populated PCBs between test lanes on a tight SMT line, where the 200 mm stroke provides full lane-clearing travel.
Actuates a folding blade on a compact packaging machine, relying on the riveted aluminum body's small footprint to fit between side conveyor rails.
Applies 206 N of pull force to seat electronic connectors onto a PCB, using the -S magnet and a DMSG solid-state switch to verify the press cycle completion.
This 25 mm bore yields 245 N push at 0.5 MPa. If you need less force, step down to the 20 mm bore (157 N push); if your load requires more, step up to the 32 mm bore (402 N push). The 200 mm stroke is well within the 500 mm standard limit, but the 10 mm rod has low side-load tolerance at this length. Use an external guide, a CA pivot back cover, or the MBLD double-rod type to prevent bending under offset loads.
The base MBL relies on a fixed rubber bumper, so choose the MBLC variant if you need adjustable air cushioning for heavier moving masses. A plain MBL does not hold its position if air pressure is lost or the valve is centered; the rod will drift. Use an external rod lock or pilot-operated check valve for fail-safe load holding. Replacement match: 25 mm bore, 200 mm stroke, G1/8 port, NPT thread, U flat-end back cover, -S magnet.
Quick checklist
At 0.5 MPa, the 25 mm bore delivers 245 N push and 206 N pull force. At 0.7 MPa, push increases to 343 N, with a maximum theoretical force of 50 kgf at 1.0 MPa. The double-acting cylinder operates at speeds of 30-800 mm/s.
No, the base MBL25X200SUT uses a fixed rubber bumper to soften end-of-stroke impact, not an adjustable cushion screw. If your application requires adjustable air cushioning for heavier loads or faster speeds, select the MBLC variant.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.