
The AirTAC MBL Aluminum Alloy Mini Cylinder MBL25X60SCAT is a genuine double-acting aluminum-barrel mini round cylinder with a Ø25mm bore and 60mm stroke, 1/8" air ports and a fixed rubber bumper. Its compact riveted body suits push, hold and clamp motion in tight machine spaces.
The AirTAC MBL25X60SCAT is a compact double-acting aluminum mini round cylinder engineered for tight machine spaces. Generating 245 N of push force at 0.5 MPa across its 60 mm stroke, it is built around a riveted rolling-packed barrel where the covers are crimped to the tube for a lightweight footprint rather than bolted tie-rods. This specific SKU features a CA pivot clevis back cover, allowing the cylinder body to swing on a pin to absorb arcing and angular loads during motion.
Because this configuration includes the -S suffix, it contains a built-in magnet for position detection using AirTAC CMSG reed or DMSG and EMSG solid-state sensor switches. The Ø10 mm carbon-steel piston rod is protected with a 20 µm hard-chrome plating to resist wear and corrosion, while a heterogeneous two-way piston seal retains grease for a long service life. End-of-stroke energy is absorbed by a fixed rubber bumper, not an adjustable cushion screw. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac MBL Aluminum Alloy Mini Cylinder MBL25X60SCAT |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder |
| Bore size | Ø25 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Rubber bumper (MBLC variant: adjustable air cushion) |
| Max stroke | Up to 500 mm |
Specifications follow the official AirTAC MBL series datasheet. Confirm against the product label before installation. Standard stroke to 500 mm (special order to 800 mm). Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | — |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| MBL | Aluminum-barrel mini round cylinder, double acting. |
|---|---|
| 25 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: MBLC (adjustable cushion), MBLD (double rod), MBLJ (adjustable stroke), MSBL/MTBL (single acting).
Ideal for small part transfer arms where the CA clevis allows the cylinder to swing naturally on a pin, handling 245 N of push force without binding during curved trajectories.
Pivots a lightweight sorting gate along a 60 mm stroke; the built-in magnet triggers a DMSG solid-state switch to confirm flap position for the PLC.
Drives a spring-loaded test fixture with precise 60 mm travel, relying on the 20 µm chrome-plated rod to prevent wear in high-cycle electronic manufacturing.
Selecting this 25 mm bore makes sense when your application requires 245 N of push force at 0.5 MPa. If you need less force, stepping down to the 20 mm bore yields 157 N of push force; if your payload is heavier, stepping up to the 32 mm bore provides 402 N. The CA pivot back cover on this specific model is critical for mechanisms with arcing rod paths, as it prevents side-load binding that would occur with a rigid flat-end U mount.
Keep in mind the fixed rubber bumper softens end-of-stroke impact but does not lock the rod; if air pressure drops, the load will drift or fall, requiring an external pilot-operated check valve for position holding. For higher kinetic energy at cycle ends, consider the MBLC variant which adds an adjustable air cushion. Replacement matching requires a 25 mm bore, 60 mm stroke, NPT port thread, CA back cover, and a magnet. The G1/8 port size is fixed by the bore.
Quick checklist
At 0.5 MPa, this 25 mm bore cylinder provides 245 N of push force and 206 N of pull force. At 0.7 MPa, the push force increases to 343 N, with a theoretical maximum of 50 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No, the base MBL features a fixed rubber bumper to soften the end-of-stroke impact and cannot be adjusted. If your application involves heavier moving masses or higher speeds requiring tunable deceleration, you should step up to the MBLC variant which includes an adjustable air cushion.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.