
The AirTAC SAID63 Double Rod Cylinder SAID63X145 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø63mm bore and 145mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID63X145 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 63mm bore and a 145mm made-to-order stroke. Because a carbon steel rod exits both end covers, the annulus area is identical on extend and retract, yielding equal bidirectional force of 1402N at 0.5MPa and 1962N at 0.7MPa. The extruded aluminum barrel includes sensor grooves on both sides for flexible mounting of CMSE reed or DMSE electronic switches.
This through-rod design allows mounting a primary workpiece on one end and a secondary cam, position flag, or external guide on the rear rod. It shares the standard ISO 15552 footprint and operates at 30-800mm/s with adjustable air cushions at both ends. Note that a plain SAID does not hold position upon air loss; for locking requirements, consider the SAIL or BSAID series.
| Model | Airtac SAID63 Double Rod Cylinder SAID63X145 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 145 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×145 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a shuttle mechanism where the equal 1402N extend and retract forces at 0.5MPa prevent speed variations and ensure consistent cycle times in both directions.
Utilizes the twin-rod guidance to keep a vertical lifting carriage perfectly square, preventing the mechanical twist that single-rod cylinders experience under offset loads.
Actuates a clamping tool on the front rod while the rear rod end drives a physical limit flag past a DMSE solid-state sensor for precise end-of-stroke confirmation.
Choose this 63mm bore when your application requires perfectly balanced push and pull forces, as both directions output 1402N at 0.5MPa. If you need higher thrust, stepping up to the 80mm bore provides 2268N both ways, while dropping to the 50mm bore offers 825N. The double-rod architecture is specifically selected over a single-rod SAI when twin-side guidance, anti-rotation resistance, or rear-rod actuation is required. This non-standard 145mm stroke is manufactured to order, so verify rear-rod clearance in your layout. Mounting accessories are limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2 (FB, CA, CB, and CR are omitted). Ports are PT tapered G3/8 threads. Since the stroke is under 300mm, standard rod bearing bending is minimal, but always ensure axial load alignment.
AirtacDistr lists every SAID63 order code with its price on one page at https://airtacdistr.com/products/airtac-said63-double-rod-iso-cylinder
Quick checklist
Because the double-rod design subtracts the rod area on both sides of the piston, the push and pull forces are equal. It generates 1402N at 0.5MPa, 1962N at 0.7MPa, and 2523N at 0.9MPa in both directions.
Yes, it is dimensionally interchangeable per ISO 15552 as a direct replacement for other double-rod profile cylinders. It supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts, but omits the FB, CA, CB, and CR accessories used on single-rod variants.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.