
The AirTAC SAID63 Double Rod Cylinder SAID63X70 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø63mm bore and 70mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID63X70 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 63 mm bore and 70 mm stroke. Because a carbon steel rod exits both end covers, the effective piston area is identical on extend and retract, yielding an equal 1402 N of force in each direction at 0.5 MPa.
This through-rod architecture allows you to mount the primary workpiece on the front rod while using the rear rod extension to drive a secondary mechanism or trigger a position flag. The extruded aluminum barrel includes sensor grooves on both sides, enabling flexible mounting of CMSE or DMSE switches if a magnet is specified later.
| Model | Airtac SAID63 Double Rod Cylinder SAID63X70 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 70 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 63 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer carriage with identical push and pull thrust, ensuring consistent acceleration and deceleration cycles without skewing.
The twin-rod geometry resists torsional twisting on linear slides, maintaining precise alignment for tooling during extension and retraction.
The protruding rear rod operates a secondary cam or mechanical valve, sequencing downstream pneumatics without adding external space.
Select this 63 mm bore when an application demands symmetric force and speed both ways, offering 1402 N at 0.5 MPa. If your payload is lighter, stepping down to the 50 mm bore provides 825 N both ways, whereas heavier loads require the 80 mm bore at 2268 N. Unlike a single-rod SAI, this twin-rod design provides superior anti-rotation guidance for the load.
This model uses PT tapered ports and supports the reduced SAID mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting FB, CA, CB, and CR. Note that the adjustable air cushions only decelerate the piston near stroke end; they do not hold the load. If position holding without air pressure is required, consider a SAIL or BSAID variant. It is dimensionally interchangeable per ISO 15552.
AirtacDistr lists every SAID63 order code with its price on one page at https://airtacdistr.com/products/airtac-said63-double-rod-iso-cylinder
Quick checklist
Because the double-rod design equalizes the annulus area on both sides, the SAID63X70 provides 1402 N of force in both extend and retract directions at 0.5 MPa, and 1962 N at 0.7 MPa.
Yes, the SAID63X70 is dimensionally interchangeable per ISO 15552. It shares the standard mounting footprint and utilizes a reduced accessory set including Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.