
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X65-20S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 65mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X65-20-S is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to fine-tune the effective travel down to a 45-65 mm window without adding external stops. The extruded aluminum barrel includes sensor grooves on both sides, and this -S variant includes a magnet for position detection.
This model uses a 16 mm carbon steel rod with an M12x1.25 thread, paired with 30 mm variable air cushions at both ends to decelerate the piston smoothly. The rear adjuster acts strictly as a travel stop for end-position tuning and does not hold the load without live air pressure. For load-holding requirements, a SAIL or BSAI cylinder is recommended instead.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X65-20S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 65 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×65 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 45-65 mm travel window during product size transitions to set new end stops rapidly without physically replacing the cylinder.
Trim the retract stroke by up to 20 mm at commissioning to perfectly time the mechanical sequence without machining external spacers.
Leverage the integrated -S magnet with DMSE solid-state or CMSE reed switches to confirm part seating within the adjusted travel limits.
The adjustable stroke prevents the need to swap cylinders for minor dimensional variations, unlike a fixed-stroke SAI model. This SAIJ variant supports a mounting subset of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR. Fluid connections use a PT tapered G1/4 port.
Because the 65 mm stroke is relatively short, side-loading stress is minimal, but the 16 mm rod still handles lateral forces better than smaller bores. If the machine cycle requires the cylinder to maintain its position without continuous air pressure, note that the rear adjuster and cushions are not a brake; you would need an external rod lock or a pilot-operated check valve. This unit is dimensionally interchangeable per ISO 15552 standards.
AirtacDistr lists every SAIJ40 order code with its price on one page at https://airtacdistr.com/products/airtac-saij40-adjustable-cylinder
Quick checklist
The rear adjuster screw allows you to shorten the 65 mm nominal stroke by up to 20 mm, creating a usable travel window of 45 to 65 mm. The adjuster functions as a mechanical stop for end-position tuning and does not lock or hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.