Airtac SC100 Standard Cylinder SC100X1350STC
The AirTAC Airtac SC100 Standard Cylinder SC100X1350STC is a genuine double-acting standard air cylinder with a Ø100mm bore and 1350mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ100 mm
- Stroke1350 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 29 mm
About the Airtac SC100 Standard Cylinder SC100X1350STC
The AirTAC SC100X1350STC is a double-acting tie-rod cylinder delivering substantial force for long linear movements. With a 100 mm bore, it generates 3927 N of push force at 0.5 MPa and up to 7068 N at the maximum operating pressure of 0.9 MPa, driven by a 25 mm diameter piston rod.
This model features a 1350 mm stroke, which is within the 1500 mm maximum standard stroke for the SC100 bore. The suffix code specifies a built-in magnet (-S) for mounting CMSG/DMSG sensors directly on the barrel, and a centre trunnion mount (TC) supplied with the TCM1 bracket for pivoting motion. Total extended body length is approximately 1538 mm.
Airtac SC100 Standard Cylinder SC100X1350STC Technical Specifications
| Model | Airtac SC100 Standard Cylinder SC100X1350STC |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 1350 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC100 Standard Cylinder SC100X1350STC
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×1350 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC100 Standard Cylinder SC100X1350STC Is Used
Long-Stroke Material Transfer
Moves heavy pallets or components across a 1350 mm span in packaging and logistics lines, using the centre trunnion mount to allow the cylinder body to pivot freely.
Large Part Clamping & Welding
Provides 7068 N of clamping force for welding fixtures on large automotive or agricultural frames, with magnetic sensors confirming full extension before the cycle starts.
Pivoting Actuator for Dampers
Operates heavy ventilation or process dampers with a 1350 mm linear stroke. The TC trunnion mount accommodates the arcing motion, while the tie-rod design handles industrial environments.
Is the Airtac SC100 Standard Cylinder SC100X1350STC the Right Cylinder?
Select the SC100 bore when your application requires push forces in the 3927 N (0.5 MPa) to 7068 N (0.9 MPa) range. If your force requirement is lower, consider stepping down to the SC80 bore, which provides 2513 N at 0.5 MPa. For higher forces, the SC125 bore offers 6136 N at the same pressure. To ensure a correct replacement, match five key specifications: 100 mm bore, 1350 mm stroke, PT port thread, centre trunnion (TC) mounting with the F-SC100TC bracket, and the built-in magnet (-S) for sensor compatibility.
For any stroke of 300 mm or more, like this 1350 mm unit, the extended rod is susceptible to bending under side loads. Always use an external guide rail or a guided cylinder assembly to protect the rod bearings and ensure reliable, long-life operation.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC100 Standard Cylinder SC100X1350STC FAQ
At the standard 0.7 MPa operating pressure, the cylinder provides 5497 N of push force and 5153 N of pull force. The maximum push force at 0.9 MPa is 7068 N. The theoretical maximum at 1.0 MPa is 801 kgf.
No. The AirTAC SC series is a tie-rod cylinder with a shorter overall body length than an ISO 15552 profile cylinder. A direct replacement must match the 100 mm bore, 1350 mm stroke, PT ports, centre trunnion mount (F-SC100TC), and the built-in magnet for sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC100 Standard Cylinder SC100X1350STC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.