
The AirTAC SC100 Standard Cylinder SC100X1860S is a genuine double-acting standard air cylinder with a Ø100mm bore and 1860mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
The AirTAC SC100X1860S is a double-acting single-rod pneumatic cylinder with a 100 mm bore and an extra-long 1860 mm stroke, delivering 3927 N of push force at 0.5 MPa. Its 25 mm diameter piston rod and 29 mm adjustable air cushion help manage end-of-stroke deceleration even at extended reaches, while the built-in magnet allows CMSG or DMSG sensors to clamp directly onto the tie-rod barrel for rod-position feedback.
Because 1860 mm exceeds the standard maximum stroke of 1500 mm for bore 100, this unit is a made-to-order non-standard stroke cylinder. The PT1/2 port threads and M20x1.5 rod-end knuckle thread match standard SC100 tooling, and the tie-rod construction keeps the body length A to a compact 188 mm before stroke extension.
| Model | Airtac SC100 Standard Cylinder SC100X1860S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 1860 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×1860 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Pushes or pulls pallets and large components across extended conveyor spans, where the 1860 mm stroke reaches deep into racking or staging areas.
Opens and closes large industrial doors or machine guarding panels, using the full 1860 mm travel for complete clearance in high-bay facilities.
Applies 3927 N of clamping force at 0.5 MPa across wide weldments or assembly fixtures, with sensor-ready position confirmation via the built-in magnet.
For applications needing slightly less force, stepping down to an 80 mm bore yields 2513 N at 0.5 MPa; for heavier push requirements, the 125 mm bore provides 6136 N at the same pressure. With a 1860 mm stroke, the unsupported rod length is significant—always use an external linear guide or rod support to prevent bending under side load, or consider a guided cylinder for off-axis forces. To ensure a direct replacement, match bore, stroke, PT port thread, the built-in magnet (-S), and the basic mounting configuration of this SC100X1860S.
AirtacDistr lists every SC100 order code with its price on one page at https://airtacdistr.com/products/airtac-sc100-tie-rod-air-cylinder
Quick checklist
At 0.5 MPa the cylinder pushes with 3927 N and pulls with 3681 N. At the maximum operating pressure of 0.9 MPa, push force reaches 7068 N. The theoretical maximum at 1.0 MPa is 801 kgf.
No. For any stroke over 300 mm, and especially at 1860 mm, side loads can bend the 25 mm rod or damage the bearing. Always install an external guide rail or rod support, or switch to a guided cylinder, to absorb off-axis forces.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.