Airtac SC100 Standard Cylinder SC100X335S
The AirTAC Airtac SC100 Standard Cylinder SC100X335S is a genuine double-acting standard air cylinder with a Ø100mm bore and 335mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ100 mm
- Stroke335 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 29 mm
About the Airtac SC100 Standard Cylinder SC100X335S
The SC100X335S is a double-acting pneumatic cylinder from the AirTAC SC tie-rod series, combining a 100 mm bore with a 335 mm stroke. At 0.5 MPa air pressure it produces a push force of 3927 N and a pull force of 3681 N, making it suitable for medium-to-heavy linear actuation tasks. The built-in magnet (suffix -S) allows direct mounting of CMSG, DMSG, or EMSG reed and solid-state sensors on the barrel for reliable end-of-stroke or mid-position detection.
This model uses a 25 mm diameter piston rod with an M20x1.5 male thread and PT1/2 port connections. Its adjustable pneumatic cushion (29 mm length) decelerates the piston smoothly at both ends, reducing impact noise and wear. The body length A is 188 mm, giving a total extended length of approximately 523 mm. Operating pressure ranges from 0.15 to 1.0 MPa with a proof pressure of 1.5 MPa, and the standard TPU seals work reliably from -20 °C to +70 °C.
Airtac SC100 Standard Cylinder SC100X335S Technical Specifications
| Model | Airtac SC100 Standard Cylinder SC100X335S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 335 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC100 Standard Cylinder SC100X335S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×335 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC100 Standard Cylinder SC100X335S Is Used
Material Transfer & Diverting
Delivers 3927 N at 0.5 MPa to shift boxes or pallets on roller conveyors. The 335 mm stroke spans wide conveyor beds, while the built-in magnet enables sensor feedback for automated sortation control.
Press & Clamping Fixtures
Applies up to 7068 N at 0.9 MPa for holding workpieces during machining or welding. The adjustable cushion protects tooling from impact, and magnetic sensors confirm clamp engagement before cycle start.
Automated Gate & Hopper Actuation
Operates sliding gates or hopper doors in bulk material handling. The 335 mm stroke provides full gate opening, while the tie-rod construction withstands dusty environments when properly filtered.
Is the Airtac SC100 Standard Cylinder SC100X335S the Right Cylinder?
Choose the SC100 bore when your application needs push force in the 3900-7100 N range at standard shop air pressures. If your load is lighter, stepping down to an SC80 (2513 N push at 0.5 MPa) can reduce air consumption and mounting footprint. For heavier loads, the SC125 bore delivers 6136 N at the same pressure. Always match replacement cylinders on five points: bore (100 mm), stroke (335 mm), port thread (PT1/2), mounting style (basic, no bracket), and magnet option (-S required for sensor compatibility).
At 335 mm of stroke, the 25 mm rod is adequately supported for axial loads, but any significant side load will create a bending moment at the rod bearing. For applications where the rod must guide or push an unconstrained mass, add an external linear guide rail or switch to a guided cylinder to protect the rod bearing and seals from premature wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC100 Standard Cylinder SC100X335S FAQ
At 0.5 MPa, push force is 3927 N and pull force is 3681 N. At 0.7 MPa, push rises to 5497 N. At the maximum operating pressure of 0.9 MPa, push force reaches 7068 N. The theoretical maximum at 1.0 MPa is 801 kgf. These values assume clean, filtered air at 40 µm and standard temperature.
Yes. The -S suffix indicates a built-in magnet band on the piston, making the SC100X335S fully compatible with AirTAC CMSG (reed) and DMSG/EMSG (solid-state) sensors. The sensors clamp directly onto the barrel tie-rods without additional brackets. For a non-magnet cylinder, order the SC100X335 instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC100 Standard Cylinder SC100X335S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.