
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X110-20 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 90 to 110 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X110-20 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M8x1.25 adjuster screw lets you dial the outward stroke from 90 to 110 mm directly on your machine, eliminating the need for shims or part swaps during changeovers. Retract remains at the full 110 mm.
This unit saves valuable axial mounting depth thanks to its short riveted body, fitting where round-body or profile alternatives cannot. The bore dictates a 10 mm piston rod, an M5x0.8 air port, and a female M5x0.8 rod-end thread. End shock is managed by a fixed NBR bumper, which decelerates the piston near the end of travel but is not an adjustable air cushion. Operating speed spans 30-500 mm/s across a temperature range of -20 to +70 C.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X110-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 110 mm |
| Adjustable range | 90 – 110 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×110 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 90 to 110 mm via the M8x1.25 screw to accommodate varied part heights during machine setup without swapping hardware.
When sizing this actuator, evaluate your force requirements against its neighbours. Choose this specific model if your fixture setup requires frequent trial positioning or on-machine stroke tuning within the 90-110 mm window.
Verify your system parameters: 25 mm bore, 110 mm maximum stroke, 20 mm adjust window, and an M5x0.8 port. This SKU lacks the -S magnet and cannot accept reed or electronic switches; add the -S option if sensing is required. Note that a plain cylinder does not hold its load when air is lost or the valve is centred—the fixed bumper only decelerates near the end of travel. For load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa. It operates at 30-500 mm/s within a 0.15-1.0 MPa pressure range.
The screw is a mechanical stop, not a mid-stroke lock; the cylinder cannot hold a load on air loss, and the fixed NBR bumper only decelerates the stroke end.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.