
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X130-20 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 110 to 130 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X130-20 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M8x1.25 adjuster screw lets you dial the forward end-position anywhere between 110 and 130 mm directly on the machine, eliminating the need for shims or part swaps during changeovers.
This thin riveted-body design saves axial mounting depth where round-body or profile cylinders will not fit. The bore uses an M5x0.8 air port and a 10 mm piston rod. End shock is managed by a fixed NBR bumper that decelerates the stroke end; it is not an adjustable air cushion. Note this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X130-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 130 mm |
| Adjustable range | 110 – 130 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×130 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 110-130 mm extend stop during prototype runs. The external screw allows incremental fine-tuning without disassembling the fixture.
Adjust the stroke on-site when switching product sizes. The compact riveted body fits into tight transfer stations where axial depth is restricted.
The fixed NBR bumper reliably decelerates the arm at the end of each cycle.
Choose this model if your setup requires frequent on-site stroke tuning between 110 and 130 mm. Confirm your parameters: 25 mm bore, 130 mm max stroke, 20 mm window, M5x0.8 port, female rod-end thread, and no magnet. Remember that a plain cylinder does not hold its load on air loss or valve centering—the piston drifts and the fixed bumper only decelerates near the end. For a held load, specify an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa. Adjusting the stroke does not alter these force values.
The M8x1.25 R screw shortens the extend stop by up to 20 mm, giving a usable forward range of 110-130 mm. This acts as a mechanical stop, not a mid-stroke lock. The cylinder cannot hold a load if air pressure is lost; use an external rod lock for load holding. This SKU also lacks a magnet for switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.