
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X25-30S is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 0 to 25 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X25-30S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. Turning the R (M8x1.25) screw lets you dial the extend position down to 0 mm from the 25 mm maximum directly on the machine, eliminating shims or part swaps.
Its short riveted body saves axial mounting depth where round-body or profile cylinders cannot fit. The unit relies on a fixed NBR bumper to decelerate the stroke end rather than an adjustable air cushion. Because the -S option is present, a built-in piston magnet enables position sensing with AirTAC reed or electronic switches.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X25-30S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 25 mm |
| Adjustable range | 0 – 25 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×25 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Quickly reset the stroke length on packaging lines handling different carton sizes, using the M8x1.25 adjuster to fine-tune the diverting arm position.
Use the built-in magnet with electronic switches to verify intermediate positions while adjusting the mechanical stop for precise test fixture alignment.
Dropping down to SDAJ20 yields 157.1 N, while stepping up to SDAJ32 provides 402.1 N. This model suits setups needing on-site stroke tuning, but note that a plain cylinder does not hold a load on air loss or valve centering; the bumper only decelerates near the end. For load holding without live pressure, install an external rod lock or pilot-operated check valve. Verify your bore, 25 mm stroke, 30 mm window, M5x0.8 port, -S magnet, and female M5x0.8 rod-end thread.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa.
The R (M8x1.25) screw shortens the extend stop by up to 30 mm, allowing a usable extend range of 0 to 25 mm. It sets the mechanical stop position and does not alter the force or act as a mid-stroke lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.