
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X35-20B is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 15 to 35 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X35-20B is a compact double-acting double-rod cylinder featuring an external extend stop. An M8x1.25 adjuster screw lets you dial the forward end-position on the machine across a 15 to 35 mm window, removing the need for shims or part swaps during changeovers.
The short riveted body minimizes axial mounting depth where round-body or profile units will not fit. This specific SKU includes a male M8x1.25 piston rod thread and lacks a piston magnet, meaning it cannot host reed or electronic switches without upgrading to the -S variant. End shock is managed solely by a fixed NBR bumper, which decelerates the stroke end but does not function as an adjustable air cushion.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X35-20B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 35 mm |
| Adjustable range | 15 – 35 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×35 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 15 to 35 mm on the machine to accommodate varying jig heights without machining new spacers.
Set precise mechanical endpoints for prototype alignment fixtures, safely decelerating the end motion via the fixed NBR bumper.
If your application requires less force, the neighboring SDAJ20 bore provides 157.1 N at 0.5 MPa; stepping up to the SDAJ32 yields 402.1 N for heavier demands. This model is ideal for setups demanding frequent on-site stroke tuning without part changes.
Confirm the 25 mm bore, 35 mm maximum stroke, 20 mm adjust window, and M5x0.8 air port match your pneumatic layout. Note that the male M8x1.25 rod thread (-B) is present, and no magnet is included. Because a plain cylinder drifts when air is lost or the valve centers, utilize an external rod lock or pilot-operated check valve for load holding, as the fixed bumper only decelerates near the end of travel.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The air port is M5x0.8.
The M8x1.25 screw shortens the extend stroke by up to 20 mm, allowing a usable forward range of 15 to 35 mm. It acts as a mechanical stop, not a mid-stroke lock, and cannot hold a load without air pressure; use a pilot-operated check valve for holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.