
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X35-30 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 5 to 35 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X35-30 is a compact double-acting double-rod cylinder featuring an external extend stop. An M8x1.25 adjuster screw lets you dial the forward end-position anywhere between 5 and 35 mm directly on the machine, eliminating the need for shims or part swaps during setup. Retract remains full length while the mechanical stop sets the limit.
The short riveted body minimizes axial mounting depth where space is tight. End-of-stroke deceleration relies on a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. This specific SKU lacks a piston magnet, so it cannot host reed or electronic switches.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X35-30 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 35 mm |
| Adjustable range | 5 – 35 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×35 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 5 to 35 mm on the fly to accommodate different jig heights during production line changeovers.
Iteratively tune the forward stroke during R&D fixturing without disassembling the cylinder to add or remove shims.
When sizing this unit, verify if the 25 mm bore hits your target payload.
Choose this adjustable variant if your application requires frequent on-machine stroke tuning or trial positioning. Note that a plain cylinder drifts when air is lost or the valve centers; the fixed bumper only decelerates near the end and the screw acts as a mechanical stop, not a lock. For load holding without live pressure, install an external rod lock or pilot-operated check valve. Confirm your bore, 35 mm stroke, 30 mm window, M5x0.8 port, female rod thread, and lack of magnet (S) before ordering.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
Turning the M8x1.25 R screw shortens the extend stroke by up to 30 mm, allowing the rod to stop anywhere between 5 and 35 mm. It sets the mechanical stop position and does not alter the output force.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.