
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X40-10 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 30 to 40 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X40-10 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M8x1.25 adjuster screw lets you dial the forward end-position anywhere between 30 and 40 mm directly on the machine, eliminating the need for shims or part swaps during changeovers.
The short riveted body saves valuable axial mounting depth where larger profile or round-body units cannot fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic sensing without upgrading to the -S variant.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X40-10 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 40 mm |
| Adjustable range | 30 – 40 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×40 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 30 to 40 mm via the M8x1.25 screw to accommodate varying part thicknesses on machining lines without swapping actuators.
Set a precise mechanical stop to press light components into housings, using the fixed NBR bumper to absorb the final end shock.
Choose the SDAJ25X40-10 if your fixture setup requires frequent trial positioning or exact forward endpoint tuning within the 30 to 40 mm window.
Confirm the 40 mm maximum stroke, 10 mm adjustment window, and M5x0.8 air port suit your manifold. This base unit has a female M5x0.8 rod-end thread and no magnet. Remember that the fixed NBR bumper only decelerates the stroke end; a plain cylinder drifts and cannot hold a load if air pressure drops or the valve centers. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa.
Turning the external R (M8x1.25) screw shortens the extend stroke by up to 10 mm, yielding a usable forward range of 30 to 40 mm. The screw acts only as a mechanical stop and does not function as a mid-stroke lock. The cylinder cannot hold a load if air is lost; use an external rod lock for holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.