
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X45-10 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 35 to 45 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X45-10 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. Turning the R (M8x1.25) screw lets you dial the outward stroke down from the 45mm maximum to 35mm directly on the machine, eliminating shims or part swaps during setup.
Its short riveted body saves valuable axial mounting depth where larger profile or round-body units will not fit. The bore uses an M5x0.8 air port and a 10mm piston rod. End shock is managed solely by a fixed NBR bumper, which decelerates the piston near the end of travel but is not an adjustable air cushion.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X45-10 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 45 mm |
| Adjustable range | 35 – 45 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×45 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 45mm down to 35mm via the M8 screw when swapping machining fixtures, avoiding the need to manufacture custom spacer plates.
Set the mechanical stop incrementally during initial machine commissioning to find the exact 35-45mm extension required for a delicate alignment task.
Choose this specific unit when your fixture requires on-site stroke tuning between 35 and 45 mm.
Confirm the 25mm bore, 45mm stroke, 10mm adjust window, M5x0.8 port, and female M5x0.8 rod-end thread suit your mounting. Note that this SKU lacks a piston magnet, so it cannot accept reed or electronic switches. Because the fixed bumper only decelerates near the end of travel, a plain cylinder does not hold a load on air loss or valve centring; for load holding without live pressure, install an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa, proof pressure is 1.5 MPa, and the operating speed range is 30-500 mm/s.
The external M8x1.25 screw acts as a mechanical stop that shortens the extend stroke by up to 10mm, yielding a usable range of 35-45mm without changing force. This specific SKU has no piston magnet, so it cannot take a switch; the -S variant adds a magnet for reed or electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.