
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X50-10 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 40 to 50 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X50-10 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M8x1.25) screw, you shorten the forward stroke on-site across a 40 to 50 mm window, eliminating the need for shims or part swaps during commissioning.
This 25 mm bore actuator features a short riveted body that saves axial mounting depth where a round-body or profile cylinder will not fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X50-10 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 50 mm |
| Adjustable range | 40 – 50 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×50 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the 40-50 mm extend stop via the R screw during machine setup to accommodate different part heights without machining new spacers.
Safely probe the optimal end position for a 12.5 kg vertical lift fixture, adjusting the stop in small increments before locking the layout.
Choose this exact model if your fixture requires on-site stroke tuning within the 40-50 mm range.
Confirm the bore (25 mm), full stroke (50 mm), adjustment window (10 mm), and M5x0.8 air port match your pneumatic layout. The rod end thread is female M5x0.8 unless you specify the male B option. Remember that a plain SDAJ does not hold position or load when air is lost or the valve is centred; the fixed bumper only decelerates near the end, and the screw is a mechanical stop, not a lock. For load holding without live pressure, integrate an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
Operating pressure is 0.15-1.0 MPa, proof pressure is 1.5 MPa, and speed ranges from 30-500 mm/s.
Turning the M8x1.25 adjuster screw shortens the extend stroke by up to 10 mm, yielding a usable forward range of 40-50 mm while retract remains full. This SKU has no piston magnet and cannot take a switch; you must select the -S option to enable AirTAC reed or electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.