
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X50-30B is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 20 to 50 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X50-30B is a compact double-acting double-rod cylinder featuring an on-site extend stop. By turning the external M8x1.25 adjuster screw, you set the forward stroke anywhere between 20 and 50 mm without changing parts.
This variant uses a male M8x1.25 threaded rod end and includes no piston magnet. Its short riveted body minimizes axial mounting depth where longer profile or round-body units will not fit. End shock is handled by a fixed NBR bumper that decelerates the piston near the end of travel; it is not an adjustable air cushion.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X50-30B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 50 mm |
| Adjustable range | 20 – 50 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×50 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 20 to 50 mm during machine setup to accommodate different jig heights without machining new spacers.
Gradually extend the male M8 rod during initial prototype runs to find the exact seating depth before locking the adjuster.
When sizing this 25 mm bore, check both neighbours.
Operators needing frequent changeover or trial positioning benefit from the 20-50 mm adjust window. Confirm your requirements for the 50 mm maximum stroke, 30 mm window, M5x0.8 port, and male M8 rod thread. Note that a plain cylinder drifts on air loss or valve centring; the bumper only decelerates the end of stroke and is not a lock. For load holding without live pressure, install an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa.
The M8x1.25 screw mechanically shortens the forward stop from the 50 mm maximum down to 20 mm. This SKU lacks a piston magnet, so it cannot take a switch; the -S variant adds a magnet for reed or electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.