
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X50-40 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 10 to 50 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X50-40 is a compact double-acting double-rod cylinder featuring an external extend stop. An M8x1.25 adjuster screw lets you dial the outward stroke down by 40 mm, yielding a usable extend range of 10 to 50 mm directly on the machine without changing parts.
The short riveted body significantly reduces axial mounting depth where a longer cylinder would not fit. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot accept reed or electronic switches; adding the -S option enables sensing.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X50-40 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 50 mm |
| Adjustable range | 10 – 50 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×50 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 10 to 50 mm on packaging lines to accommodate varying carton depths without swapping hardware.
Set precise upper travel limits for 12.5 kg lifting fixtures, ensuring repeatable heights without relying on hard machine frames.
This makes the 25 mm ideal when the smaller bore lacks thrust and the larger is physically too wide.
Operators requiring frequent trial positioning or rapid format changeovers benefit most from the 10-50 mm on-site tuning. Remember that a plain SDAJ does not hold a load if air pressure drops or the valve is centred; the piston drifts until hitting the bumper. For suspended or vertical loads, specify an external rod lock or pilot-operated check valve. Confirm your bore, stroke, window, M5x0.8 port, female rod thread, and lack of magnet for this configuration.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa, with a proof pressure of 1.5 MPa and a speed range of 30-500 mm/s.
Turning the R (M8x1.25) screw mechanically shortens the extend end-position by up to 40 mm, giving a usable outward stroke of 10 to 50 mm. The screw sets the stop only and does not alter force. It is not a mid-stroke lock; the cylinder cannot hold a load if air is lost, so use an external rod lock for suspended loads.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.