
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X70-20B is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 50 to 70 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X70-20B is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M8x1.25 adjuster screw lets you dial the outward stroke down by up to 20 mm directly at the machine, yielding a usable extend range of 50 to 70 mm without swapping shims or parts.
Built with a short riveted body, this unit saves axial mounting depth where a round-body or profile cylinder will not fit. The bore sets the piston rod at Ø10 mm, and this B-option configuration provides a male M8x1.25 rod-end thread for direct mounting. End-of-travel deceleration relies on a fixed NBR bumper rather than an adjustable air cushion, and this specific SKU lacks a piston magnet, so it cannot accept magnetic switches.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X70-20B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 70 mm |
| Adjustable range | 50 – 70 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×70 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop between 50 and 70 mm via the M8 screw to accommodate varied part heights on machining fixtures without fabricating new spacers.
Use the 20 mm adjust window to probe the exact contact point for a 12.5 kg vertical lift jig, locking the mechanical stop once the optimal geometry is found.
Choose this model if your fixture requires on-site stroke tuning during setup or tooling changeovers.
Confirm the 70 mm maximum stroke, 20 mm adjust window, and M5x0.8 air port for your plumbing. This SKU includes the male M8x1.25 piston rod (-B) and no magnet. Remember that a plain cylinder does not hold its load on air loss or when the valve is centred—the piston drifts and the fixed bumper only decelerates near the end. For a held load, specify an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa. The adjuster screw does not alter these force values.
The M8x1.25 screw shortens the extend stop by up to 20 mm, giving a usable outward range of 50 to 70 mm. This specific SKU has no piston magnet and cannot take a switch; ordering the -S variant adds a magnet for AirTAC reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.