
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X80-20S is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 60 to 80 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X80-20S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M8x1.25 adjuster screw lets you dial the outward stroke down by up to 20 mm directly on the machine, yielding a usable extend range of 60 to 80 mm without swapping shims or parts. Retract remains full length.
This riveted-body design saves valuable axial mounting depth where a larger profile cylinder will not fit. It relies on a fixed NBR bumper at each end to decelerate the stroke, which is not an adjustable air cushion. Equipped with a built-in piston magnet (-S), the unit supports AirTAC reed or electronic solid-state switches for end-position sensing. The 10 mm rod uses a female M5x0.8 end thread, and the body ports are M5x0.8.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X80-20S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 80 mm |
| Adjustable range | 60 – 80 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×80 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop between 60 and 80 mm during fixture swaps to accommodate varying part heights without machining new spacers.
Iterate the extend endpoint in millimetre increments during R&D prototyping to find the exact contact point before locking the M8 screw.
Choose this specific model when you need on-site stroke tuning for trial positioning or frequent changeovers.
Confirm your parameters: 25 mm bore, 80 mm maximum stroke, 20 mm adjust window, M5x0.8 port, and the -S magnet for sensing. The female M5x0.8 rod thread handles the load, though you should avoid side loading. Note that a plain cylinder does not hold its load if air is lost or the valve centres; the piston drifts and the fixed bumper only decelerates near the end. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa.
The M8x1.25 screw shortens the extend stop by up to 20 mm, giving a usable outward range of 60 to 80 mm; retract is unaffected. The built-in -S magnet works with AirTAC reed or electronic solid-state switches for position feedback.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.