
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X90-10 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 80 to 90 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X90-10 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M8x1.25 adjuster screw lets you dial the outward stroke from 80 to 90 mm directly on your machine, eliminating the need for shims or part swaps during changeovers. Retract remains full length, while the thin riveted body saves valuable axial mounting depth where larger profile cylinders cannot fit.
End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot accept reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X90-10 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 90 mm |
| Adjustable range | 80 – 90 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×90 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the 80-90 mm extend stop on machining fixtures to compensate for tool wear, ensuring precise part clamping without fabricating new spacer blocks.
Validate end-effector reach in prototype assemblies by turning the M8x1.25 screw to find the exact 10 mm sweet spot before locking down the sequence.
Choose this model if your setup requires fine-tuning the extend position within the 80-90 mm window without swapping components.
Confirm your parameters: 25 mm bore, 90 mm maximum stroke, 10 mm adjustment window, and an M5x0.8 port. The rod-end thread is female M5x0.8 (or male M8x1.25 if option B is specified). Keep in mind that a plain SDAJ does not hold position or load when air is lost or the valve is centered; the fixed bumper only decelerates near the end. For load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The adjustment screw does not alter these force values.
Turning the external R (M8x1.25) screw shortens the extend end position anywhere between 80 and 90 mm. The screw acts only as a mechanical stop and does not lock the piston mid-stroke; for load holding without air pressure, you must use an external rod lock or pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.